Recommended Replacement Electric Brakes for a 2018 Lance 1985 Trailer

Question

Question:

Can you please tell me which product I need if you have it. I am looking for a replacement brake kit for my 2018 Lance 1985 Travel Trailer. It has electric brakes and 14 wheels.

asked by: Andrew R

0

Expert Reply:

I looked up your trailer and it looks like it has a GVWR of 5,700 lbs which likely means you have 3,500 lb axles so the etrailer Electric Trailer Brakes # AKEBRK-35-SA would work fine.

These brakes are self-adjusting meaning you won't have to periodically adjust them, will work with 13" to 15" wheels, and includes both the left and right hand side.

expert reply by: Bryce D

0

Answer 1

Hey Brad, thanks for all of the info on what you have. I can tell your magnets are basically toast, the brake pads look thin, and your hub/drums look like they are in bad shape too so your best option is to go with new assemblies left and right with…

view full answer...

Answer 2

Given the wheel bolt pattern and the 8-247 that's cast into your existing brake drums, you have a 3500 lb axle. Assuming you have E-Z Lube spindles with the grease zerks in the end, you'd want to use the #AKHD-545-35-EZ-K hub/drums you looked…

view full answer...

Answer 3

I contacted Dexter with the serial number from your Dexter Torsion axle on the 2019 Lance 1985. The outer bearing is part #L44649 and the inner bearing is part #L68149 with a Dexter seal 010-019-00 which measures 1.719" inner diameter. You can…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 11

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 12

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...