Solution for Needing Replacement Prop Rod Assembly Ends for Leer Tonneauas

Question

Question:

My 2019 Ford Ranger Leer cover prop rod lever broke. Can I just get the ends of the rod or do I need to buy new rod? Model is HF 350 M, part number is 631303. Thanks.

asked by: Dan K

0

Expert Reply:

We don't have a way to get just the replacement ends for the prop rod assemblies. Only solution would be the complete rod like part # LE54MR.

expert reply by: Jameson C

0

Answer 1

By poles I'm assuming you're talking about the gas struts that hold the cover up against the rear window. These poles can be replaced with the Replacement Prop Rod Assembly for Leer Tri-Fold Tonneau Covers #LE72RR. We also carry the…

view full answer...

Answer 2

Thank you for providing that information. What you need is the Replacement Prop Rod Assembly for Leer Tri-Fold Tonneau Covers #LE44MR.

view full answer...

Answer 3

Replacement prop rods are available for most tonneau covers but we'll need to know the exact model of your tonneau cover to determine the correct replacements. For example, Leer has multiple prop rods for different tri-fold models, like part…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hey Melanie. The reason you can't find a replacement for your GE ARC15AACBL2 15,000 btu air conditioner is because they phased them out. In 2025 all RV AC systems had to change over to a new coolant called R32. This was a EPA mandated decision.…

view full answer...

Solution for Needing Replacement Prop Rod Assembly Ends for Leer Tonneauas

Continue Researching