Replacement Hydraulic Brake Actuator for Homemade Trailer With Short Tongue
Published 01/03/2024
Products Featured in This Question
Question:
I purchased a homebuilt trailer years ago. it came with a hydraulic brake boat hitch. It was in pretty terrible condition when i bought it and it never really worked good, well it finally broke to the point of no return. the tounge itself is a 3in x3in and only 5.5in long. Tandum axle 7k lbs. What is the recommendation?
asked by: Devon S
Expert Reply:
I'm assuming you have hydraulic drum brakes and actually need the brake actuator. If that is the case, you're looking at either extending the tongue so you can bolt on an actuator like the # DX33FR or welding one on like the # DEX94FR. Both have a 7,500 lb capacity and are compatible with drum brakes.
If it were me, I would stick with the bolt on option and get a local trailer shop to extend the tongue a bit. This would also make for an easier swap in the future should you need to replace it again. There probably isn't much of a cost difference between extending the trailer tongue slightly and paying a professional welder to install the weld-on coupler to what you have now. That will also give you a little more room to work with so everything isn't cramped.
If you don't need an actuator then the Demco Channel Tongue Trailer Coupler # 12564 you looked at could work if you extended the trailer tongue. If the distance between those bolt holes is 3" then you could use the Demco Channel Tongue Trailer Coupler # DM13689-95. All you would need to do is drill the third hole on the bottom for installation.
(click to enlarge)
Product Page this Question was Asked From
Demco Straight Tongue Trailer Coupler - eZ-Latch - Zinc - 2" Ball - Bolt On - 10,000 lbs
- Straight Tongue Trailer Coupler
- Standard Coupler
- 2 Inch Ball Coupler
- Bolt-On
- 10000 lbs GTW
- 3 Inch Channel
- Auto Latch
- 4-Bolt
- Marine Grade
- Demco
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: dexter a~60
- Shop: Dexter DX7.5L A-60 Brake Actuator with Fill Cap - Bolt On - Drum - 2" Ball - Zinc - 7,500 lbs
- Q&A: Replacement Trailer Coupler Recommendation for an Atwood 87558
- Shop: Dexter DX7.5 Drop-N-Go Brake Actuator - Drum Brakes - 2" Ball - Zinc Plated - 7,500 lbs
- Video: Review of Dexter Brake Actuator - Surge Brake Actuator - DX33FR
- Q&A: Replacement Trailer Actuator for UFP A-70
- Shop: Replacement Inner Member for Dexter DX7.5L Brake Actuator - Drum - 2" Ball - 7,500 lbs
- Q&A: Replacement Hydraulic Drum Brakes, Hub/Drum, and A-60 Actuator for 3,500 lb Axles on Boat Trailer
- Q&A: Recommended Surge Brake Actuator for a 3" x 5" Tongue
- Q&A: Replacement For TDE LP7000 Surge Brake Actuator
- Shop: Dexter DX7.5L A-60 Brake Actuator - Weld On - Drum - 2" Ball - Primed - 7,500 lbs
- Video: Review of Demco Straight Tongue Trailer Coupler - Bolt On eZ-Latch 2 Inch Ball Silver - DM15000-52
- Shop: Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K
- Shop: Demco Straight Tongue Trailer Coupler - eZ-Latch - Zinc - 2" Ball - Bolt On - 10,000 lbs
- Q&A: Replacement Inner Member for UFP A-60 Drum Brake Actuator
- Shop: Replacement Inner Member for Dexter DX7.5L Actuator - Tandem Axle w/ Disc - 2" Ball - 7,500 lbs
- Q&A: What Grade Bolts Are Recommended To Install Demco Channel Tongue Trailer Coupler
- Search Results: trailer safety chains
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Search Results: bunk
- Search Results: bunk carpet
- Search Results: coupler hardware
- Search Results: break away
- Video: Complete Breakdown of the Demco Channel Tongue Trailer Coupler
- Video: Feature Review Dexter Hydraulic Trailer Brake Kit
- Video: LED Identification Light Bar for Trailers over 80" Wide Review
- Video: Comprehensive Review: Optronics LED Clearance or Side Marker Light
- Video: LED Identification Light Bar for Trailers over 80" Wide: The Breakdown
- Search Results: trailer coupler repair
- Article: How to Bleed Your Trailer Surge Brakes