Width of Hangers Included With Single-Axle Trailer Hanger Kit for Double-Eye Springs

Question

Question:

How wide are the hangers on this part?

asked by: Wylin W

0

Expert Reply:

The larger hanger that comes with the # APS1 is 2-5/16" wide on the outside and 1-7/8" on the inside. The smaller hanger is 1-13/16" on the outside and 1-3/8" on the inside. These are designed to work with your standard 1-3/4" wide double-eye leaf spring. I have attached the full dimensions below.

expert reply by: Robin H

0

Hanger Dimensions
(click to enlarge)

Answer 1

The correct height for your Reese Select Plus 5th Wheel Trailer Hitch #RP30081 really depends on your fifth wheel trailer and truck setup. Basically you want your trailer to sit as level as possible so you will need to pick the correct height…

view full answer...

Answer 2

You can use the 30" Long 6-Leaf Double-Eye Spring for 5,000-lb Trailer Axles item #UG34FR in place of a 29-1/2" leaf spring but you may need to modify your suspension or get a shorter equalizer. If you have a tandem axle trailer you should…

view full answer...

Answer 3

The Curt 16027 OEM puck system rail adapter which we offer as part #C88KR would add 2-1/2 inches to the installed height of your 5th wheel hitch. From what I read online, the top of the PullRite 2900 sits 18-1/2 inches tall so using the #C88KR would…

view full answer...

Answer 4

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 5

Hey Jason, it's pretty common for replacement leaf springs to be slightly shorter than what they replace as springs tend to stretch/flatten overtime as they wear out so while you are on the right track 3/4 of an inch is a bit too much of a…

view full answer...

Answer 6

Hello John, thanks for reaching out. For the wet bolts you can measure the overall length or the length not including the head. Honestly when replacing this stuff, the bolts are going to be a standard length and diameter. Typically I would not even…

view full answer...

Answer 7

Hey Jay, yes the wet bolts for the suspension hangers are included with the MORryde X-Factor part #MR33WR that you referenced. In the attached picture you can see the new looking silver wet bolt holding the CRE3000 equalizer.

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Width of Hangers Included With Single-Axle Trailer Hanger Kit for Double-Eye Springs

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching