Can Trailer with Slipper Springs have Double Eye Springs attach to Same Hanger Channel
Updated 12/26/2023 | Published 12/23/2023
Question:
I have a single axle, rated at 2K, 4 x 8 ft foldable utility trailer with slipper springs. The hangers are welded to the trailer frame as one piece for bolt attachment of the single eye and slipper see uploaded picture. I want to replace slippers with double eyes. Since the hangers are integral with the frame and are at the same level/height can I buy shackles shortest length possible to add to the OEM hanger so I can use the double eyes? Do I need a shackle for the front and rear eye to keep the trailer/leaf spring level? Im thinking if I installed 2 inch shackles this will raise my trailer height 2 inches. If I installed the shackles would there be any concerns I should have?
asked by: Walter
Expert Reply:
You have a really interesting suspension setup on your trailer. I don't know what the width of the channel is that your springs attach to but to go to a double leaf will require using a hanger kit like the part # APS4 that you referenced. If you were to add shackles to the rear hanger area the spring would be unlevel and you can't add them to the front as well. Plus you have to factor in that you most likely would not have room for two shackles and springs in the channel currently.
So what I would recommend doing is having a weld on hanger kit like the part # APS4 welded to your frame so that you can use a double eye spring. Or you could stick with slipper springs and keep the setup as-is.
(click to enlarge)
Product Page this Question was Asked From
Single-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4" Front, 1-1/4" Rear
- Trailer Suspension Parts
- Hangers
- Suspension Kits
- Boat Trailer
- Camper
- Car Hauler
- Snowmobile Trailer
- Utility Trailer
- Double Eye Springs
- Single Axle
- etrailer
more information >
Continue Researching
- Shop: Trailer Idler Axle Beam with Easy Grease Spindles - 72" Long - 2,000 lbs
- Q&A: Are Leaf Spring Bushings Hard to Replace
- Shop: CE Smith Trailer Axle w/ Idler Hubs - 5 on 4-1/2 - 57-1/2" Long - 1.8K
- Shop: EZ Loader Over the Frame Hanger for 2" Wide Frame - 13/16" Bolt Hole - Qty 1
- Search Results: 30~1/2 inch long trailer leaf springs
- Search Results: square axle ~ 1~1/2 inch trailer suspension parts
- Search Results: trailer axles
- Shop: Trailer Axle Beam with Easy Grease Spindles - 86-1/2" Long - 5,200 lbs
- Q&A: How To Determine Correct Axle Placement For Single Axle Trailer
- Shop: Trailer Idler Axle Beam with Easy Grease Spindles - 60" Long - 2,200 lbs
- Shop: Trailer Idler Axle Beam with Easy Grease Spindles - 60" Long - 2,000 lbs
- Q&A: What Torque Rating Should be Used to Install Trailer Suspension Shackle Bolts
- Q&A: Are there Bolt-On Hangers for Trailer Leaf Spring Suspension
- Q&A: Determining Hanger Spacing for Replacement Leaf Springs on Trailer
- Q&A: Do Suspension Hangers Need to Welded on Or Can They be Bolted On
- Shop: Terran Industries Single-Axle Hanger Kit for Double Eye Springs - 1-1/2" Tall Front
- Q&A: Looking For Square Tube Marine Axle For Boat Trailer
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Shop: Trailer Hitch
- Video: Measuring To Choose The Right Trailer Axle
- Shop: Trailer Wiring
- Search Results: trailer tires and wheels
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer wiring
- Article: How to Measure for Trailer Hitch Drop
- Shop: Suspension Enhancement
- Shop: Brake Controller
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Video: Review of etrailer Trailer Hubs and Drums - Hub with Drum - AKHD-545-35-EZ-K
on Trailer Suspension Parts
