Availability of Optronics Trailer Clearance Lights that are 2-1/2 inch by 1-1/4 inch

Question

Question:

Hello I have a 2006 Sundowner 2 horse gooseneck trailer with optronics marker lights. They are 2 1/2 inches long, 1 1/4 inches wide aid 1 inch tall. I need both the red and amber colors. Do you sell these lights?

asked by: James M

0

Expert Reply:

We do have Optronics trailer clearance lights that match the dimensions you mentioned with the part # AL90AB for amber and part # AL90RB for red.

expert reply by: Jameson C

0

Answer 1

It looks like you're looking for the Mounting Grommet w/ Built-in Wedge for A91 or AL91 Series Lights part #A91GZB which has a built-in wedge and is designed for Optronics A91 Series Clearance Lights.

view full answer...

Answer 2

The Optronics FLEET Count Mini Thinline Sealed LED Marker/Clearance Light #AL90RB has a single LED element while the similar Thinline LED Clearance and Side Marker Light #AL91RB has three LEDs for brighter output and it is submersible. Both can mount…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Availability of Optronics Trailer Clearance Lights that are 2-1/2 inch by 1-1/4 inch

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching