Which Timbren Kit for 2024 GMC Sierra 1500

Question

Question:

Which Timbren do I need for my 2024 GMC Sierra 1500? I'll be towing a travel trailer.

asked by: Pedro

0

Expert Reply:

The rear Timbren kit you'd want for your 2024 GMC Sierra 1500 is the part # T28MR which is the standard duty version. This will give you a better blend of support and ride quality than the severe duty version part # T53MR which would be a lot harsher.

expert reply by: Jameson C

0

Answer 1

Both the Timbren and he Roadactive part #RAS54FR would work for getting rid of the sag you mentioned but the RAS kit is for sure the winner. The Timbrens get the job done but they are notoriously harsh when loaded and unloaded whereas the RAS kits…

view full answer...

Answer 2

Congrats on the new truck! The Timbren item #T28MR will work and it'll keep the rear end of your 2023 GMC Sierra 1500 from squatting but they're also going to give you a rough ride when you are not towing or have your camper. They're just…

view full answer...

Answer 3

The Timbren Suspension Enhancement System part #T28MR and SumoSprings Solo Custom Helper Springs part #SS45FR are both great options for a 2021 GMC Sierra 1500 AT4. I recommend the SumoSprings as they don't typically ride as rough as the Timbrens…

view full answer...

Answer 4

Yes, the Timbren Suspension Enhancement System #T28MR will be the best option when it comes to cost-effectiveness. This will fit with your 2021 Chevrolet Silverado 1500 Z71 Trail Boss but you'll want to make sure these fit the gap properly. The…

view full answer...

Answer 5

While I can confirm the Timbren Rear Suspension Enhancement #T28MR will fit your 2024 Chevy Silverado 1500 ZR2, I would be hesitant to put such a heavy spring on your truck. I would personally select the SumoSprings #SS65FR as these will actually…

view full answer...

Answer 6

I checked your order notes and the leaf springs you bought last year were the part #e28SR which are for 5k axles. Since this is over the capacity of your axle failure would not have been caused by over loading the trailer assuming you stayed under…

view full answer...

Answer 7

In order to get the correct replacement springs (as you need to replace springs in pairs for any given axle) I'll need you to lift the trailer by the frame so the leaf spring is relaxed, and then measure from the center of one bolt hole to the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Which Timbren Kit for 2024 GMC Sierra 1500

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching