Air Lift Analogue Gauge AL25195 - Can The Low Pressure Cutoff Be Reset?

Question

Question:

i have the air lift analog gauge how do you set the low cutoff pressure mine stays at 20#

asked by: Ben S

0

Expert Reply:

I checked with my contact at Air Lift and I was told that there is no way to reset the low pressure cutoff on their analog gauges like the # AL25195. If it is stuck at 20 it may be a defect with the gauge. If it is still under warranty, you can get it replaced thru air lift. If it is out of warranty you will need to buy a new one.

expert reply by: Jesse M

0

Answer 1

Yes we have just the replacement gauge you are looking for with the part #AL25195.

view full answer...

Answer 2

Yes, since the Replacement Dual Analog Gauge for Air Lift Load Controller Compressor System #AL25195 is a replacement gauge for the #AL25852 which is a dual path setup that allows for having two different pressure settings like you are looking for.

view full answer...

Answer 3

The Replacement Air Gauge #AL25194 comes with only the gauge and wiring. To add a mounting bracket you need the Mounting Kit #AL25196 as well. Attached is a review video for you to check out!

view full answer...

Answer 4

Hey Jacob, The Replacement Dual Analog Gauge #AL25195 can be used, as long as you have all of the wiring hooked up correctly. I was able to find a wiring diagram for this gauge and I'm attaching that photo to this page for your reference.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hi Steve; the factory hitch on the 2013 Tacoma has the bumper brackets integrated into the hitch. You can replace it with the etrailer Trailer Hitch #e98850 but you will have to remove the old hitch and find new bumper brackets to complete the…

view full answer...

Answer 10

Hey Fernando, I'd be happy to help you pick out the correct Timbren rear suspension kit for your 2023 Toyota Tacoma TRD that will be towing a trailer. Really it comes down to two options. You would want the part #TTORTUN4L for if you have the 3…

view full answer...

Answer 11

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 12

The aftermarket hitches for a 2011 Toyota Tacoma don't fit alongside the factory installed hitch; some trucks have hitches you can add on to OEM hitches that fit underneath the original. So I can't see any reason why you wouldn't be able…

view full answer...

Air Lift Analogue Gauge AL25195 - Can The Low Pressure Cutoff Be Reset?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching