Can Multiple Valterra Waste Valve Extensions be Ran Together

Question

Question:

I have a 2008 winnebago View. I just replaced both drain valves Valterra valves and need two new 17inch handle extension tubes . I dont see that length but is there a way to connect two tubes together to get close to that length? Doesnt have to be exact, Thank you

asked by: Kurt S

0

Expert Reply:

Yes, you can connect multiple Valterra waste valve extensions like the part # TX8HPB together to get a longer handle like you are wanting.

expert reply by: Jameson C

0

Answer 1

Hello Jacob, thanks for reaching out. There are a lot of different locks that can work with the Demco Ez-latch coupler. To be honest, any lock can be defeated, it is just a matter of how difficult the lock would be to defeat. A really good all-around…

view full answer...

Answer 2

Great questions! The safe working load limit that you see on products like the Curt Safety Chain Quick Link #C82932 has to do with everyday use. So, if you were to use this quick link to regularly pull something Fulton doesn't recommend exceeding…

view full answer...

Answer 3

The standard Valterra replacement valves like the part #T1003PBC are designed to attach to a remote handle that's further away while the Valterra Bladex like part #T1003VP the handle is right at the valve instead. Both valves are interchangeable…

view full answer...

Answer 4

There isn't a guide showing the exact black tank waste valve used on your 2016 Airstream so I have a few examples for valves you can use. If you are replacing just the valve between two flanges then the Valterra Bladex Waste Valve Body for RV…

view full answer...

Answer 5

Sounds like instead you would want the part #T1003VP which is a similar valve as the #T1003PBC except it comes with the T handle. The part is ABS plastic, so you could use an ABS sealant or glue. The glue is not included though. Part number #A05-0303…

view full answer...

Answer 6

The Valterra Bladex Waste Valve Body for RV Black Water Tank part #T1003VP will replace the valve but the part that you have now has a 3" spigot hub on both sides. This valve would require some modifying to fit into the same place as your old…

view full answer...

Answer 7

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 8

Hey Mike! The Power Mountain Tallboy Off-Road Bottle Jack #PM34FR can be stored in that manner (with the oil plug facing up), but my contact at Power Mountain stressed that it should only be done for a short period of time, so I recommend setting it…

view full answer...

Answer 9

Hey Todd! At the lowest setting, the saddle of the Power Mountain Tallboy Off-Road Bottle Jack #PM34FR sits at 14" and the top of the saddle arms are at 15-3/8". I took a photo of it out in our warehouse, and while I wasn't able to get…

view full answer...

Answer 10

Hi Carl; the saddle attachment on the Power Mountain Tallboy Off-Road Bottle Jack #PM34FR is 3-1/4" wide at the base of it before the sides flare out. What will you be using the jack for?

view full answer...

Answer 11

Hey Frank, We would need to know the diameter and shape of the footplate for your tongue jack in order to find the correct SnapPad to fit it.

view full answer...

Answer 12

Hello Ken. The Lippert Scissor Stabilizer Jacks #LC285326 are only intended to be used as a stabilizer, they are not supposed to be used to lift. For your Polaris General XP 4 1000 I recommend the Power Mountain Tallboy Off-Road Bottle Jack -…

view full answer...

Can Multiple Valterra Waste Valve Extensions be Ran Together

Product Page this Question was Asked From

Continue Researching