Mounting Curt Venturer NEXT Trailer Brake Controller

Question

Question:

How would one go about mounting the Curt Venturer NEXT brake controller? It doesn't hang down I see.

asked by: Chris

0

Expert Reply:

Curt has started using new brackets for their brake controllers, and that is also true for the Curt Venturer NEXT Trailer Brake Controller # C74VV.

To mount this, all you have to do is put the included adhesive tape onto the included bracket and stick it wherever you like under your dash. If you'd like, you can also use the included screws with the adhesive to mount the bracket under your dash. With the bracket mounted, you'll just slide the Venturer NEXT controller into the bracket and that's it.

This type of bracket takes up less space than the normal bracket most brake controllers come with, giving you a bit more leg space in your cab. So you can get a better idea of how it looks, I have added a photo showing the bracket of the Curt Venturer NEXT # C74VV.

expert reply by: Kyle S

0

Curt Venturer NEXT Brake Controller Mounting
(click to enlarge)

Answer 1

Most likely you blew a fuse if the brake controller screen one day stopped working. But that also depends on how the controller was installed. Basically the black wire of the brake controller needs to have 12 volts ran to it and the white needs to…

view full answer...

Answer 2

Based on my research it does look like the 2018 Chevy Traverse is equipped with blunt cut wires beneath the dash for installing a trailer brake controller as part of its standard package. To be certain of this you can visit a local Chevy dealer with…

view full answer...

Answer 3

The Tekonsha Prodigy P3 Trailer Brake Controller part #90195 with the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers part #3024-P is indeed a good choice for a 2020 Ram 1500. In regards to installation, the plug is located behind the…

view full answer...

Answer 4

According to my research, you are not alone in having a difficult time finding the factory trailer brake controller wiring on your 2018 Buick Enclave. I was able to find a tech bulletin on your Buick Enclave that describes exactly where the wiring…

view full answer...

Answer 5

I checked with Tekonsha and they state that your 2019 Buick Enclave with the factory tow package (factory 7-way) can have a brake controller installed but there isn't factory wiring so you'll need to hardwire it to the vehicle. For that you…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Actually, the P3 now has the upgraded axis accelerometer like the P2. The Tekonsha P3 Trailer Brake Controller #90195, will work with both electric over hydraulic brakes on the trailer as well as electric brakes. It has a menu option on the display…

view full answer...

Answer 12

The best replacement option we offer for a Atwood GC10A-4E Water Heater is tankless, the Furrion RV Tankless Water Heater part #FR68SR. It won't be a direct replacement but still pretty easy nonetheless as they are very similar. That said, you…

view full answer...

Mounting Curt Venturer NEXT Trailer Brake Controller

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching