Will The Bauer Products Compression Latch # BA67FR Work On A 2-1/2" Thick Ramp Door

Question

Question:

Will this work on a 2 1/2 inch thick door?

asked by: Alex

0

Expert Reply:

The Bauer Products Compression Latch # BA67FR unfortunately is only going to work with 2" thick doors. You could potentially use the 4" version # BA87FR and cut the bolt down to fit your door and then use a die tool to cut threads further down the bolt as needed.

expert reply by: Kevin C

0

Answer 1

The only difference between the Firestone Ride Rite Red Label 5000-lbs Air Bags #F35FV and the 7500-lbs Air Bags #F95FV is the material that they are constructed with; both air bags will be the same size, but the 7500-lbs air bags are constructed…

view full answer...

Answer 2

You did no damage using a lube plate on your pin box. Lube plates are great for pin boxes that rotate to keep from getting grease everywhere, but a Revolution pin box does not rotate at the hitch, so the RV dealer should not have recommended it for…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Hey Tim welcome back! Your ARH15AACBL2 GE AC unit has the old 410a refrigerant in it so the GE Appliances item #GE64FR you were looking at isn't going to work as a replacement. The EPA mandated R32 refrigerant has been used in all new AC's…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Will The Bauer Products Compression Latch # BA67FR Work On A 2-1/2" Thick Ramp Door

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching