Availability of Conversion Kit to Adapt Utility Trailer to Malone Crossbars/Kayak Carrier

Question

Question:

Do you still offer a conversion kit for regular trailers to carry kayaks?

asked by: Dale R

0

Expert Reply:

Sounds like you are looking for the Malone Crossbar Conversion Kit part # MPG475. This allows you to convert a standard utility trailer to having a set of Malone Crossbars which you could then use a Malone kayak carrier like the # MPG107MD on.

expert reply by: Jameson C

0

Answer 1

The U-Bolts that arrive with the Malone Crossbar Conversion Kit #MPG475 Hardware Kit are 1/2" U-Bolts that 6" long & 2" wide.

view full answer...

Answer 2

I checked with Malone about the Malone Crossbar Conversion Kit for Standard Utility Trailer part #MPG475 and confirmed the weight capacity as 400 lbs evenly distributed.

view full answer...

Answer 3

The Malone Crossbar Conversion Kit for Standard Utility Trailer #MPG475 that you referenced has the weight capacity of the Malone crossbars that come with the kit of 400 lb.

view full answer...

Answer 4

Either one is fine to do. With the Fulton Hi-Mount Spare Tire Carrier part #FSTC1000301 you are not going to be adding a great deal of width to your trailer so the difference is minimum. Giving you my opinion since there is no rule I would Choose the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Availability of Conversion Kit to Adapt Utility Trailer to Malone Crossbars/Kayak Carrier

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching