Pre-Greased Trailer Hub for Floe Pro 100 Snowmobile Trailer

Question

Question:

Hi I have a floe pro 100 2 place snowmobile trailer. Looking for prepacked hub assembly. 5- 4 1/2 bolt pattern.

asked by: Jared

0

Expert Reply:

From previous customers who have the same Floe Pro 100 trailer we have determined that the correct replacement hub would be for a 2k axle like with the part # AKIHUB-545-2-1K which is pre-greased.

expert reply by: Jameson C

0

Answer 1

Luckily, FLOE International is still around. I was able to find that your 10 foot tilt single axle snowmobile trailer used an L44649 inner and outer wheel bearing. Your snowmobile trailer was equipped from the factory with idler hubs that had a 5 on…

view full answer...

Answer 2

We don't currently carry any torsion axles. You also have a unique frame width, so I have an alternative solution for you. I recommend the Timbren Axle-Less Trailer Suspension System with Hubs - 5 on 4-1/2 - Regular Tires - 2,000 lbs #A20RS545 or…

view full answer...

Answer 3

We do have a spindle that fits that description with part #TRU44FR. This uses two #L44649 (1.063" inner diameter) bearings and a #10-9 (1.50" inner diameter) grease seal.

view full answer...

Answer 4

I'm assuming you mean a U-bolt kit to mount your axle to the leaf springs on your FLOE Pro 100 snowmobile trailer. The correct kit will depend on your capacity/axle diameter. If you have a 2k axle that uses hubs like the #34822545BX you were…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Pre-Greased Trailer Hub for Floe Pro 100 Snowmobile Trailer

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching