Availability Of Suspension Hanger Bracket With Mounting Holes Near 3 On Center

Question

Question:

This part looks perfect I need the width of the bolt holes to be right at 3” Can you point me to the right part number? Thanks

asked by: Jay A

0

Expert Reply:

The CE Smith Front Hanger Bracket # CE14016G is the closest we have the Bracket # CE14026G. This hanger places the mounting holes at 3-3/8" on center.

expert reply by: Bud M

0

CE Smith Front Hanger Bracket # CE14016G Mounting Hole Dimensions
(click to enlarge)

Answer 1

Hey James, thanks for the information! To replace the brakes on your 1985 EZ Loader trailer, I recommend the Hydraulic Brake Kit item #AKFBBRK-35-D. These are a pair of 3,500 lbs of 10" brake assemblies that fit a 4-bolt brake mounting flange.…

view full answer...

Answer 2

Hey Larry welcome back! To replace the braking hubs and self-adjusting brake assemblies on your 2014 Keystone Montana 3100rl you will need the following parts: Easy Grease Trailer Hub and Drum Assembly item #AKHD-865-7-2-EZ-K. This EZ lube hub is…

view full answer...

Answer 3

I've got a solution for you. Unfortunately the CE Smith Front/Rear Hanger Bracket for Double-Eye Springs - part #CE14026G you looked at aren't going to work. I measured the mounting hole on it and they are on 1 9/16" centers which means…

view full answer...

Answer 4

The replacement upright for your #CE27620 CE Smith 40" Post-Style Guide-Ons is #CE27608PG. The mounting hardware for the upright is #CE11452-A.

view full answer...

Answer 5

Hey Ryan! I would say that something about that measurement is off. I have never seen an incorrect axle tag before so it is safe to assume 92-1/2" is the length. That being said, we do not carry any axles that match your measurements. The only…

view full answer...

Answer 6

The bolt hole spacing for the CE Smith Front/Rear Hanger Bracket for Double-Eye Springs #CE14026G is 4-3/8" x 1-5/8". I've attached a dimensional photo for you to check out as well as a review video to reference.

view full answer...

Answer 7

Hey Bruce, You can swap out your current equalizer for a taller one, like the #TREQ310 you were looking at, but you could run into fitment issues and might need to replace the shackle straps, hangers, or even the leaf springs to accommodate the…

view full answer...

Answer 8

If you are looking to replace your current EQ-310 equalizers with the same thing then we have that equalizer listed on our site as part #TREQ310. Then to replace your shackle straps you can simply filter through our linked selection of shackle straps…

view full answer...

Answer 9

The center hangers in the Tandem-Axle Trailer Hanger Kit #APT8 that you recently purchased are indeed longer. This is actually pretty common for tandem axle trailers. The reason for the extra length on the middle hanger is related to the shackle…

view full answer...

Answer 10

It does look like you have shackle straps that are to long and possibly worn out bushings. You can replace your shackles with the 2-1/4" Shackle #LC122487. You will need 8 of these for the entire trailer. I would recommend pulling a couple of…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...