Installing Brake Controller on 2021 Jeep Wrangler Rubicon without Tow Package
Published 09/19/2023
Products Featured in This Question
Question:
I’m installing a break controller on a 2021 Jeep Wrangler Rubicon, that I assumed had the towing package. It had the plug under the driver side dash. I installed it and plugged it in but the controller didn’t light up. I read your article about it may need fuses in f36 or f37. The 2 fuse spots do not do not accept fuses. Any thoughts?
asked by: Micah K
Expert Reply:
You'll most likely want to hardware your brake controller to your vehicle then since the tow package wiring is not completed. So what you'll want to do is run 10 gauge wire from the black wire of the brake controller like part # 10-1-1 (sold by foot) up to vehicle battery positive post through a breaker like # 9510 and then also run a length of 10 gauge wire from the blue wire back to the blue wire of your 7-way and you'd be set.
There isn't a way we can help activate your missing tow package and I am sure it would be pretty expensive to try and do that through Jeep.
Continue Researching
- Search Results: redarc trailer brake controller
- Search Results: 4 to 7 pin adapter
- Search Results: redarc liberty
- Shop: Brake Controller
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Trailer Wiring
- Video: Comprehensive Review: Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness
- Video: A Closer Look at the Redarc Encapsulated Power Diode for Tow-Pro Brake Controllers
- Video: Detailed Breakdown of the Buyers Products Trailer Connector Adapter
- Shop: Trailer Hitch
- Shop: Suspension Enhancement
- Q&A: Troubleshooting Pollak Trailer Connector Adapter Not Working With Kioti DK5010 Tractor
- Q&A: Recommended 7-Way Connector for a 2024 Jeep Wrangler Unlimited w/out the Tow Package
- Q&A: Where To Connect Red Wire Of Redarc Tow-Pro Liberty To 2016 Kia Sorento W/ Adaptive Cruise Control
- Q&A: Installing a Redarc Trailer Brake Controller on 2021 Jeep Wrangler with Brake Pedal Sensor
- Q&A: Brake Switch Signal Without Tapping into Factory Wiring On 2021 Toyota Highlander For Brake Control
- Q&A: Recommended 7-Way Connector for a 2023 Jeep Wrangler Unlimited w/out the Factory Towing Package
- Shop: Vehicle Tow Bar Brake System
- Shop: Redarc Tow-Pro Liberty Brake Controller w/ Universal Wiring Harness - Dash Knob - Proportional
- Shop: Universal Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers
- Shop: Air Lift 1000 Air Helper Springs for Coil Springs - Rear
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Redarc Tow-Pro Liberty Brake Controller - Dash Knob - Up to 2 Axles - Proportional
- Shop: Air Lift 1000 Air Helper Springs for Coil Springs - Rear
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Q&A: Brake Controller Install on 2021 Jeep Wrangler Unlimited
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Feature Breakdown: Universal Installation Kit for Trailer Brake Controller
- Video: In-Depth Review of the Universal Installation Kit for Trailer Brake Controller
- Search Results: 307300
on Trailer Brake Controller
