Overall Width of U-Bolts of Curt # C68WR

Question

Question:

Pictures say the measurements are 3 1/4” across the top? Is it the same measurement center to center across the open end?

asked by: Justin B

0

Expert Reply:

Yes, the u-bolts of the # C68WR have the same overall width of 3-1/4 inches on the bottom and top. The studs are perfectly parallel.

expert reply by: Jameson C

0

Replacement Safety Chain Anchor Kit U-Bolt Measurement
(click to enlarge)

Answer 1

The Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box - Lippert 1621 and 1621 HD - 18,000lbs - 3.5K TW #325-GH-8040 has a standard king pin so you will have no issues coupling to your Andersen Ultimate 3220 Fifth Wheel Hitch.

view full answer...

Answer 2

I went out to the warehouse and measured the Replacement Safety Chain Anchor Kit for Curt EZr Double Lock Underbed Gooseneck Trailer Hitch #C68WR that you mentioned, and measured 3-7/8" for the longest sections, 3-1/4" across the top, and…

view full answer...

Answer 3

If the U-Bolt you're needing to replace is part of the bracket kit #C60648 then you'll need to get the whole installation kit unfortunately - I confirmed this with my contact at Curt. The only other U-Bolts used in the Curt EZr Double Lock…

view full answer...

Answer 4

To determine where to cut the 4 inch diameter hole to install the B&W Turnoverball Underbed Gooseneck Trailer Hitch w/ Custom Installation Kit #BWGNRK1257 in your 2011 Toyota Tundra you will need to measure from the tail gate end of the truck bed…

view full answer...

Answer 5

The Buyers Products Gooseneck Safety Chain U Bolt Kit #337BRB03 has an overall length of 5-5/8 inches and a length of 4-3/4 inches that is below the top of the truck bed. The diameter is .57 inches and the on center measurement is 1-7/8 inches.

view full answer...

Answer 6

The U-bolt in the B&W Replacement Safety Chain U-Bolt Kit, #BW1900-2-1600, measures 3-1/4 inches long x 2-1/2 inches wide. The inside measurement of the U-bolt is 1-9/16 inches. The U-bolt is also 1/2 of an inch in diameter. The attached photo…

view full answer...

Answer 7

Hey Troy, I am thinking that your axle is rated for either 9,000 or 10,000 lbs. The #28580 inner and #25580 outer bearings are the sizes for what we call a #99 spindle. The #99 trailer spindle is typically found on 9,000 lb and 10,000 lb axles. It is…

view full answer...

Answer 8

I spoke with my contact at Lippert and although she wasn't able to provide me with the center of the king pin to first hole measurement, I do have the back of the mounting plate to center of the king pin measurement for you for the #LC328492.…

view full answer...

Answer 9

The distance from center of king pin to front row of bolt holes on the Curt Flex Air 5th Wheel Pin Box #LC369535 is 20-3/4". This would be a bit longer than the MORryde Cushioned 5th Wheel Pin Box for 18K to 21K Trailers w/ Lippert Rhino #MR55QR…

view full answer...

Answer 10

If the outer diameter of your spindle where the seal rides is 1.719 inches and the diameter on your hub is 2.565 the #RG06-050 would be the closest matching grease seal we offer. You will need a digital or dial caliper for this measurement like…

view full answer...

Answer 11

You could do that, or you could just use the Blaylock EZ Jack and Wheel Chock #EZ-JACK on either the inner or outer dually trailer wheel and achieve the same effect. I attached a review video for this product for you to check out as well.

view full answer...

Answer 12

The Blaylock EZ Jack and Wheel Chock, part #EZ-JACK, should have no problem working with your tandem trailer suspension. Unless your suspension works differently than the standard equalizer suspension, you should be able to use the #EZ-JACK for a…

view full answer...

Overall Width of U-Bolts of Curt # C68WR

Product Page this Question was Asked From

Continue Researching