Replacement Safety Chain U-Bolt Kit for B and W Gooseneck Hitch 1314

Question

Question:

I have a bandw 1314 hitch and was need replacement safely chain u bolts kit.

asked by: Tony S

0

Expert Reply:

Hey Tony, the correct safety chain U-bolt kit you need for your B and W Turnoverball hitch part # BWGNRK1314 is the part # BW1900-2-1600. Did yours break in action??

expert reply by: Jameson C

0

Tony S.

2/12/2025

Jameson, The chain kit you recommended did not fit my hitch set up. I end up getting them at the factory. They said there was two designs for the 1314. The kit you recommended was not wide enough. They didn't brake just got bent loading wood in bed.

Reply

Jameson C.

2/12/2025

@TonyS Sorry to hear that! I had no idea there were two designs for that hitch.

Reply

Answer 1

If you check out the sticker or plate on the pin box of your trailer currently there will be a model number listed that will help us identify what pin box you have and then from there pick out the correct Goose Box. If not there is a way you can…

view full answer...

Answer 2

The U-bolt in the B&W Replacement Safety Chain U-Bolt Kit, #BW1900-2-1600, measures 3-1/4 inches long x 2-1/2 inches wide. The inside measurement of the U-bolt is 1-9/16 inches. The U-bolt is also 1/2 of an inch in diameter. The attached photo…

view full answer...

Answer 3

If the U-Bolt you're needing to replace is part of the bracket kit #C60648 then you'll need to get the whole installation kit unfortunately - I confirmed this with my contact at Curt. The only other U-Bolts used in the Curt EZr Double Lock…

view full answer...

Answer 4

I went out to the warehouse and measured the Replacement Safety Chain Anchor Kit for Curt EZr Double Lock Underbed Gooseneck Trailer Hitch #C68WR that you mentioned, and measured 3-7/8" for the longest sections, 3-1/4" across the top, and…

view full answer...

Answer 5

The Buyers Products Gooseneck Safety Chain U Bolt Kit #337BRB03 has an overall length of 5-5/8 inches and a length of 4-3/4 inches that is below the top of the truck bed. The diameter is .57 inches and the on center measurement is 1-7/8 inches.

view full answer...

Answer 6

Yes, the u-bolts of the #C68WR have the same overall width of 3-1/4 inches on the bottom and top. The studs are perfectly parallel.

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...