What Lead Leg for Landing Gear Will Fit the Stromberg Carlson Electric Landing Gear Motor LG-142178

Question

Question:

What lead leg for landing gear should I get for the 142178 landing gear motor?

asked by: Renee

0

Expert Reply:

The Replacement Motor for Stromberg Carlson Electric Landing Gear # LG-142178 will work with Stromberg Carlson model(s) LG-1 or LG-2 and most electric landing gear sets, including Atwood, Venture, and Lippert models.

You don't really pair the lead leg to the motor, you would find a motor that is compatible with your landing gear/lead leg. If you have one of the systems above, you would be good to go with the # LG-142178. If you are needing a lead leg that is compatible with a motor and your current landing gear is not, a landing gear set like the Landing Gear Set w/ Handle # RVLG-8HDL would be a compatible set with the # LG-142178 motor.

expert reply by: Scott S

0

Answer 1

To determine the correct replacement landing gears for your 1995 Fleetwood Terry you'll want to measure the inside to inside and outside to outside measurement of the weld stops on your current landing gear set so we can see if there's a…

view full answer...

Answer 2

The first thing you want to do before you find a replacement is to check the rating on your current landing gear. You want the new landing gear to be rated for at least the same amount. You will also need to measure the weld stops to make sure they…

view full answer...

Answer 3

Yes, the Lippert Motor for Electric Landing Gear part #LC142178 that you said you have will work with the Landing Gear Set part #RVLG-8HDL. The switch you have now can then be reused or we have the Lippert Components 5th Wheel RV Landing Gear Switch…

view full answer...

Answer 4

The only difference between these two 8,000 lb landing gear sets - other than price - is that one comes with the crank handle and the other does not come with the handle. - Comes With Crank Handle: Landing Gear Set w/ Handle #RVLG-8HDL - Comes…

view full answer...

Answer 5

The only difference between the #RVLG-8HDL and the #RVLG-8000 is that the #RVLG-8HDL includes the manual crank handle, while the #RVLG-8000 doesn't. The dimensions for both are the same. • Retracted Height of 32-3/4 inches • Extended Height of…

view full answer...

Answer 6

Hi Bob; are you referring to the Landing Gear Set w/ Handle #RVLG-8HDL you purchased a little over a year ago? If so, the correct motor is the Lippert Venture 5th Wheel RV Landing Gear Motor #LC142178. If you were looking for something else please…

view full answer...

Answer 7

Hey Chad, From the top weld to the middle of the crank shaft is 6" for the Landing Gear Set #RVLG-8HDL. If you were talking about the rod at the top of the gearbox then that would be 8-1/2". Attached are some dimensional photos for you to…

view full answer...

Answer 8

Hey Bobby! As far as the jacks go for item #RVLG-8000 and item #RVLG-8HDL there is absolutely nothing different. The item #RVLG-8HDL comes with the manual handle that I have attached a picture of below. That is the only difference. If your 2019…

view full answer...

Answer 9

Hi Terry, A motor #LC142178 and switch #37213635 can be added to the Landing Gear Set w/ Handle #RVLG-8HDL to make raising and lowering the legs easier. Replacement legs aren't currently available so you'd have to buy the entire set.

view full answer...

Answer 10

Hey Bob, Landing gear components aren't all interchangeable between brands so I'd need to know the exact model to find replacement parts for your current system. If you're just wanting to replace the landing gear as a whole then I'll…

view full answer...

Answer 11

If the brand of landing gear you have now on your Keystone Laredo is a Ram brand then yes you could reuse it's motor with the #RVLG-8HDL. But most likely you have a Lippert set of landing gear based on what typically they used so instead the part…

view full answer...

Answer 12

Yes, a motor #LC142178 can be installed on the Landing Gear Set #RVLG-8000 to automate the landing gears. This motor can draw up to 30 amps DC so you'll want to run it to a switch #37212825 and then the battery with a circuit breaker #PK54230…

view full answer...

What Lead Leg for Landing Gear Will Fit the Stromberg Carlson Electric Landing Gear Motor LG-142178

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching