Replacement Grease Seal For Kodiak Disc Brakes To Fit Spindle With 1.68"

Question

Question:

Is there a huge difference between the 1.68 ID seal and the 1.71 ID seal? My kodiak brakes came with the 1.71 x 2.56, and the UFP DB-42 brakes appear to have come with 1.68 x 2.56 according to their specs.

asked by: Matt

0

Expert Reply:

You will need to replace the 1.71" ID Seal # 58846 which came on your Kodiak Disc Brake Kit # KOD59FR with the 1.68" ID Seal # 168255TB. The larger seal would allow grease to escape and moisture and dirt to get inside the hub and damage the bearings.

expert reply by: Bud M

0

Answer 1

The Easy Grease Trailer Idler Hub Assembly for 3.5K Axles part #AKIHUB-545-35-G-EZ-K is a direct replacement for a UFP H-1377.

view full answer...

Answer 2

While we do not carry a replacement cap which will allow you to convert your hubs from oil bath to grease we do have a hub and all the components you will need to install a new setup which can be filled with grease. You will need one of each per hub.…

view full answer...

Answer 3

In order to find the correct replacement bearings and grease seal for your 2007 EZ Loader trailer you will have to take a look at your current bearings. Once you remove your bearings and grease seal, you will be looking for the part number on the…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 9

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Grease Seal For Kodiak Disc Brakes To Fit Spindle With 1.68"

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching