Availability Of Snap Pads To Fit a 7" Square Landing Gear Leveling Leg

Question

Question:

do you carry any 7 or 7.25 SnapPads ? I couldnt find any on your website.

asked by: Ric S

0

Expert Reply:

We do carry the SnapPads # SP24FR4 which are designed to fit 7" square jack feet. This is a 4-pack but we also carry them as a Single # SP24FR if you only need 1 or 2.

expert reply by: Bud M

0

Answer 1

Hey Lisa, thanks for reaching out. What you'll likely need for the 7" octagon foot pads on your 2025 Coachman Entourage are the following: - SnapPad BF 7 Jack Pads for Quadra Bigfoot Leveling Systems w/ 7" Square Jack Feet - Qty 4…

view full answer...

Answer 2

Hi Molly, No, the bulb is not replaceable on this light part #328-002-04W. Since it uses a built in LED, if the light ever stops working, you would replace the entire fixture rather than just swapping out a bulb. The good news is that LEDs are…

view full answer...

Answer 3

Hey Rex! Those are some great questions. A weight distribution hitch (WDH) isn't always needed but in your case you will want one. Typically if the weight of your trailer is more than 50% of the weight of your vehicle it is a good idea to use a…

view full answer...

Answer 4

Hey Guy, welcome back! For your Equalizer Leveling System, you'll need the SnapPad EQ Compact Jack Pads item #SP24FR4. These are designed specifically for the feet on your landing gear. They're going to attach directly to them and remain on…

view full answer...

Answer 5

Based on the information I could find you are going to need the SnapPad EQ Compact Jack Pads #SP24FR4. I have included an image you can use to verify your feet do look the same to fit these pads.

view full answer...

Answer 6

While I have never seen them made of rubber there are the Sway Bracket Jackets #EQ95-01-5150 made of plastic. These were designed for those who found the noise to be excessive between the metal brackets and spring bars. They are made by Equal-i-zer…

view full answer...

Answer 7

Hey David thanks for the information! I recommend the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control item #EQ37120ET. This system has a tongue weight range of 800 lbs - 1,200 lbs so you'll be covered if you load your trailer up…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 10

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

The best replacement water heater for your Atwood GC6AA-10E is the Dometic RV Water Heater #DMC74FR which needs a cutout of 12-3/4" tall x 12-3/4" wide x 19-7/8" deep to fit. Then you just need a door like the 12-3/4" #DMC58FR to…

view full answer...