Replacement Front Roller for a Surg-o-Matic Model 6 Actuator

Question

Question:

My trailer has a Surg-o-matic Model #6. The roller that allows the unit to slide back and fourth has cracked in half along its length. Will the roller on the Titan Unit #T1601900 fit as a replacement roller on the actuator I have? Thank you for you assistance

asked by: Phill P

0

Expert Reply:

The correct replacement front roller for your Surg-o-Matic Model 6 actuator is part # T1776300. The front roller, # T1601900, that you referenced was designed to fit the Model 10 and 20 actuators and would not fit your actuator.

expert reply by: John H

0

Answer 1

Thanks for the picture Richard, I can tell by your picture you have a Model 6 surge actuator on your trailer which the #T4846500183 is the correct replacement for if you were wanting a channel style inner slide member replacement.

view full answer...

Answer 2

I have attached for you below an exploded parts breakdown of the Titan/Dico Model 10 Surge Brake Actuator. In regards to the Replacement Top/Bottom Bearing part #T1020900 and Replacement Side Bearing part #T1242700, these work to help stabilize the…

view full answer...

Answer 3

The replacement Hand Wheel Lock for Model 6 and 60 Actuator, #T2338300, contains one hand wheel lock and does not come with a spring. For replacement springs you will want the Latch Repair Kit for Titan Multi-Fit Couplers and Brake Actuators…

view full answer...

Answer 4

The correct replacement front roller for your Model 6 actuator is the part #T1776300 that you referenced.

view full answer...

Answer 5

The Replacement Inner Slide Channel for Dexter Model 6 #T4846500183 has a shank that measures 3" wide x 2-1/2" tall to it's a little smaller than the 3" square shank that comes on the Replacement Inner Slide for Demco DA91…

view full answer...

Answer 6

The B&W Tow and Stow line of ball mounts, including the #BWTS20049B, will be too wide for the Lock N Roll #336VS503 to fit around, so I can say that one is a no go right off the bat. With that out of the way, the #336VS503 will fit in the channel…

view full answer...

Answer 7

I spoke with my contact at Lock N Roll about the Lock N Roll Articulating Hitch part #336VS503505 and they were not quite sure what measurements you are looking for nor was I. That said, I went out to our warehouse for you and jotted down a few…

view full answer...

Answer 8

The Lock N Roll #336VS517 has a rise or drop of 4 1/2", and the Lock N Roll ##336VS503505 has a rise or drop of 4 1/4". The main difference between the 2 Lock N Roll hitches #336VS503505 and #336VS517 is that the #336VS503505 is adjustable.…

view full answer...

Answer 9

I had our warehouse measure the Lock N Roll Articulating Hitch for 2" Receivers - 4-1/2" Drop/Rise #336VS517 you were looking at, and from the center of the hitch pin hole to the center of the hole that the pin on the trailer side connector…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Replacement Front Roller for a Surg-o-Matic Model 6 Actuator

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching