Rough-In Required For The Lippert Flow Max RV Toilet

Question

Question:

How close to the wall can this toilet be installed?

asked by: John

0

Expert Reply:

The Lippert Flow Max RV Toilet # LC67AF requires approximately 11-1/4" of space from the wall to the center of the drain.

expert reply by: Kevin C

0

Answer 1

The Dometic 300 Toilet, #DOM64FR has a total length of 19-3/4" with a minimum distance from wall to center of 8-1/2". The Dometic 320, #DOM87FR is overall length of 22" with a minimum distance from wall to center of 11". If you…

view full answer...

Answer 2

The Dometic 300 Weekender RV Toilet part #DOM64FR that you referenced does come with a base seal so you would not need to provide that separately. No additional components are needed to install this.

view full answer...

Answer 3

You can use your existing supply line with the metal nut on your Dometic 300 Weekender #DOM64FR. However, you want to be careful since it is easy to cross thread when you have a metal nut which will damage the fitting. If you want to get a supply…

view full answer...

Answer 4

Yes, I've made a little list below of the different rough-in measurements for each toilet part number: #DOM74FR - 8.5" #DOM64FR - 8.5" #DOM24FR - 8.75" #DOM57FR - 10" #DOM37FR - 10" #DOM77FR - 10" #DOM67FR - 10"…

view full answer...

Answer 5

Hello Floyd, thanks for reaching out. That is an interesting spot for a toilet. What I would do in this case is simply measure from the back of the toilet to the center of the hole in the floor. That will tell us what kind of rough-in measurement…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 11

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Rough-In Required For The Lippert Flow Max RV Toilet

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching