Solution for Replacement Parts for Fulton T1802 Winch

Question

Question:

Good morning I would like to replace the part for my trailer winch t1802 1800lbs

asked by: Angelo B

0

Expert Reply:

The Fulton T1802 was discontinued quite a while ago. Unfortunately, this means that replacement parts for the winch are no longer around. The best solution is to replace it with a similar winch like the Fulton Single Speed Trailer Winch - 1,800 lbs # F142306.

I have attached an installation video below for your reference.

expert reply by: Robin H

0

Fulton T1802
(click to enlarge)

Answer 1

While I cannot find the exact specifications for the hole pattern on the Fulton 142208 I was able to find dimensions for the Fulton High-Performance 2-Speed Trailer Winch #F142416. It is going to have the same bolt pattern as the Fulton Winch…

view full answer...

Answer 2

I believe that the holes in the drum are meant to wind a cable through but not a strap. The strap should be held on with a bolt that is close to the center of the drum. If you need the bolt then all you will need is a 1/4 bolt, 2-1/2 inches long,…

view full answer...

Answer 3

I went out to our warehouse to take some measurements of the mounting base on the Fulton Single Speed Trailer Winch #F142306. The plate itself measures 6 inches long and 4 inches wide. The mounting pattern features a few oblong holes that allows it…

view full answer...

Answer 4

The Fulton High-Performance 2-Speed Trailer Winch #F142412 that you referenced does not come with a strap. It is compatible with a 2 inch wide strap and the drum can accept a strap length of up to 20 feet. With this in mind the Fulton #FWS20HD0200…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Solution for Replacement Parts for Fulton T1802 Winch

Featured Help Information

Miscellaneous Media

Continue Researching