Does The Etrailer Hitch Reciever e48AR Require Drilling Into The Frame Of A 2023 Jeep Compass

Question

Question:

Hello I am wanting to order your trailer hitch part e48AR for my 2023 Jeep Compass. I want to know if this will require me to drill into the frame of the vehicle. Am hoping for a no drill install. Thanks.

asked by: Franklin

0

Expert Reply:

Installation of the etrailer hitch # e48AR will not require you to drill any additional holes into the frame. That said, you likely will need to enlarge the access holes in the frame. This can be done with a drill, file or rotary tool. So while technically we call this a "no drill" install, you will still need a drill to complete your install. You also will be trimming the bumper fascia and heat shield. All of the hitches we carry for your vehicle will require these same steps.

I have linked the manufacturer instructions below if you want to take a closer look.

expert reply by: Jesse M

0

Answer 1

I would be happy to! To add a hitch to your 2023 Jeep Compass, I recommend the etrailer item #e48AR. This hitch is custom fit and bolts to your Jeep with included hardware. I really like this hitch because the crosstube mounts behind your rear bumper…

view full answer...

Answer 2

Yes, there is a hitch available for your 2023 Jeep Compass. I recommend the etrailer Hitch item #e48AR. This hitch is custom fit and bolts to your Jeep with included hardware. I really like this hitch because the crosstube is hidden behind the rear…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...