Replacement Leg for Happijac 4600 Camper Jacks

Question

Question:

I have a set of Happijac electric 4600 Jacks that have become dry and difficult to use. The motors all work fine so I would like to replace the jack legs. What would be the replacement part.

asked by: Stuart B

0

Expert Reply:

For a replacement leg for the 4600 Happijac the part # LC736515 is correct.

expert reply by: Jameson C

0

Answer 1

We currently offer 34-1/2" Lift #LC736514 and 36-1/2" Lift #LC759927 replacement legs for HappiJac Truck Camper Jack Systems and both are compatible with the 4600 series. I'd like to see some pictures of your motors and how they attach…

view full answer...

Answer 2

Hello Zach. The TorkLift Tie Downs #TLF2022A and #TLF3008A will work with your 2022 Ford F-350 short bed but the front tie downs will not be compatible with the AMP Research Powered Running Boards as they will get in the way of each other. You would…

view full answer...

Answer 3

I took a look in the owner's manual for the HappiJac Camper Jack 4600 and found the following under maintenance which I have attached for you below. Therefore, no, it's not advised to completely disassemble the jack to service the screw per…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Replacement Leg for Happijac 4600 Camper Jacks

Product Page this Question was Asked From

Continue Researching