Height from Mounting Flange to Top of Grease Cap of etrailer Hub # AKHD-655-6-K

Question

Question:

Can you tell me the measurements from the base of the wheel studs to the tip of the grease cap when installed? I am trying to verify possible clearance issues on the inside of the wheels. If possible, is a technical drawing of the part abailable which contains measurements?

asked by: Martin

0

Expert Reply:

I attached a picture that shows the dimension you are looking for on the trailer hub # AKHD-655-6-K. You'll note there are two different size caps that come with the hub.

expert reply by: Jameson C

0

Mounting Surface to Top of Dust Cover Dimension
(click to enlarge)

Answer 1

It does! I checked with Lippert for you and the exact replacement that matches up with your 814202 hub is the part number you listed: - Easy Grease Trailer Hub and Drum Assembly for 6K Axles #AKHD-655-6-G-EZ-K

view full answer...

Answer 2

We don't have that exact part number but for basically the exact same hub except made by Dexter you'd want the part #8-219-13UC3. This is the sam 6k-7.2k hub with an 8 on 6-1/2 inch bolt pattern that uses 9/16 inch studs just like the one you…

view full answer...

Answer 3

Dexter hub drum assembly #8-219-13UC3 is a replacement for your hub drum according to my contact at Redneck Trailer Supply. This is rated for 7K, has a 8-on-6-1/2 bolt pattern and 9/16-inch studs. You can also identify compatible replacement…

view full answer...

Answer 4

In order to select a correct replacement hub for the damaged unit on your Jayco 5th Wheel trailer you will need to match several identifiers from the original. First, you will want to note the axle capacity, which is usually found on a sticker or…

view full answer...

Answer 5

The Dexter Trailer Hub and Drum Assembly for 5,200-lb to 7,000-lb Axles - 8 on 6-1/2 - 9/16" Studs #8-219-13UC3 will fit on your Lippert axle. They use the same size bearings and seal.

view full answer...

Answer 6

Hey David, the 4,400 lb trailer axle is one of the most mysterious and confusing axle capacities in the world of trailer parts...Sometimes it uses parts that are for a 3,500 lb axle, sometimes a 4,400 lb, and sometimes the bigger 5,200-7,000 lb…

view full answer...

Answer 7

From that number you supplied, it appears you have axles that are 5,200-lb to 6,000-lb with a 12" - 6 on 5-1/2 bolt pattern. For brake assemblies I recommend #AKEBRK-7R-SA for the right hand side and #AKEBRK-7L-SA for the left. This is a…

view full answer...

Answer 8

Hey Mark, thanks for all of the info you listed about your hub. With just that info we know that the hub/drum part #AKHD-655-35-EZ-K that you referenced is an exact replacement.

view full answer...

Answer 9

Hi Craig; thank you for providing those part numbers. That is the 2.25" inner diameter grease seal so for replacement bearings you can use the Bearing Kit, LM67048/25580 Bearings, 10-36 Seal #BK3-300 you were looking at. If you prefer Timken…

view full answer...

Answer 10

Hey James, thanks for reaching out. We may have a suitable replacement for that, but I looked everywhere online and I could not find a widely published dimension chart or full spec sheet you can pull up online using that number alone. The only…

view full answer...

Answer 11

Hey Lawrence thanks for the information! I wasn't able to find any good pictures of the inside of your Axle Tecknology BD2-655 drums. What you'll need to do is pull one of the hubs off and look at the inside. If they're smooth like the…

view full answer...

Answer 12

Nick, absolutely. Many vanlifers wire the Velit 2000R 12V AC Unit #VE87QV so it runs while the alternator tops off the batteries. It keeps the living space cool while driving long stretches, and when you park, your bank’s already partly replenished.…

view full answer...

Height from Mounting Flange to Top of Grease Cap of etrailer Hub # AKHD-655-6-K

Product Page this Question was Asked From

Continue Researching