Valve Stem that Can be Used with Aluminum Sendel Series T07 Black Machined Trailer Wheel

Question

Question:

Which valve stems will work with these wheels?

asked by: Randy

0

Expert Reply:

You could use the Americana Metal Bolt In Valve Stem part # AM20906 with the Trailer Wheel part # AM97XR. Since this is metal it will hold up really well and can handle higher tire pressures as well.

expert reply by: Jameson C

0

Answer 1

Yes, the Aluminum Sendel Series T07 Black Machined Trailer Wheel #AM97XR will work with your 205/75R15 tires. The 205/75R15 tire will fit rim widths of 5-inch, 5-1/2-inch, 6-inch and 6-1/2-inch and the #AM97XR are 6-inch. From what I can find on the…

view full answer...

Answer 2

Hello Lindsey. I tried to do an internet search on the wheel information you sent, but could not find a definite answer. Most of the wheels that came up on my search is a 5 on 4 1/2 bolt pattern. I have included a print out so you can verify that is…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 6

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

I apologize for any confusion on what the proper torque specs are for 1/2 inch lug nuts on trailer wheels. I attached a picture of a chart to the right that details what the proper torque specs are for a trailer wheels lugs based on lug size, wheel…

view full answer...

Valve Stem that Can be Used with Aluminum Sendel Series T07 Black Machined Trailer Wheel

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching