Is the Lock Plug for the Thule Crossroad Foot Pack Handle Replaceable?

Question

Question:

Im looking for the replacement lock hole plug that will fit the crossroad foot pack handle. Is that part sold separately? Thanks!

asked by: Marcus

0

Expert Reply:

The plug on the Replacement Handle Assembly for Thule Crossroad Roof Mounted Railing Feet # 753-20064 is not offered separately as a replacement. To get another plug, you'd have to purchase the entire replacement handle.

expert reply by: Bryce D

0

Answer 1

I have a solution for you as Thule does not offer a separate tension bolt for your Crossroad TH450 Roof Mounted Railing Foot. They only offer the Replacement Handle Assembly #753-20064, the Endcap #853-3593 and the Foot #753-3399. The Foot will…

view full answer...

Answer 2

On the top of each foot on the Crossroads roof rack feet #753-3399 and Handle Assembly #753-20064 there is a shroud that goes around the bars. When the roof rack is tightened it will pull this shroud down and hold the bar firmly in place. Take a look…

view full answer...

Answer 3

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 4

Yes, you can use the new Thule SquareBar Evo Crossbars, part #TH712500, with your old Thule Crossroad footpack. The dimensions are the same, so the new bars will slide through that opening. The endcaps are different so you will need the Replacement…

view full answer...

Answer 5

The difference between the end caps is simply that the Thule Load Bar Replacement End Caps THEC1 are the older version of replacement end caps, while the Replacement Endcaps for Thule SquareBar Roof Racks #TH1500052968 are direct replacement caps for…

view full answer...

Answer 6

Yes, the part #853-2297 is a fit for Thule square crossbars as this is designed for the Thule Goalpost TH997 which comes with a Thule square crossbar.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Is the Lock Plug for the Thule Crossroad Foot Pack Handle Replaceable?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching