Replacement Circuit Board for MaxxFan 4951KS RV Roof Vent

Question

Question:

I am looking for a circuit board for a Maxxfan 4951KS SN 2017-03-A4951KS-A00577. I see a 4751KS listed on your site. Is this a compatible part with what I need?

asked by: Paul F

1

Helpful Expert Reply:

The correct circuit board for your MaxxAir MaxxFan 4951KS fan is the Replacement Printed Circuit Board for MaxxAir MaxxFan Plus Roof Vents # MA10A04751KS. It also works with The MaxxAir MaxxFan 4751KS and 4761KS models as well.

expert reply by: Jameson C

1

Answer 1

We do not carry an exact replacement unit for the MaxxAir Deluxe 8951K. We have the Smoke #MA00-07500K or White #MA00-07000K which would be the closest replacement. These fans use the same lift and fan motors but the control panels and circuit boards…

view full answer...

Answer 2

I've had this same question before and when I reached out to MaxxAir they told me that the correct circuit board replacement for the 4900K is the part #MA10A21275K.

view full answer...

Answer 3

Thanks for the picture! Based on what you are describing it sounds like the leak is coming from the motor. There wouldn't be anything that would leak out of the operator mechanism. We have the Replacement 12-Volt Variable Speed Fan Motor for…

view full answer...

Answer 4

I've attached the owners manual for your 4900K model which is similar to the #MA00-04500K model. It sounds like your operator mechanism is bad according to my tech contact at MaxxAir. For your 4900K model you will want the Replacement Operator…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

Hey Tom, congrats on the new truck! Typically when we hear that someone has the OEM tow prep package they mean the puck system. This is going to be five circular holes built into the bed of your Ram truck and is by far the best way to attach a 5th…

view full answer...

Answer 11

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 12

Hi Glen, It will depend on what the GVWR (gross vehicle weight rating) is of your trailer to determine which B&W 5th wheel to gooseneck adapter will work best for you. Fifth wheels and gooseneck trailers go off of pin weight instead of tongue…

view full answer...

Replacement Circuit Board for MaxxFan 4951KS RV Roof Vent

Product Page this Question was Asked From

Continue Researching