How Do You Unplug The Wiring Connector On Tekonsha Prodigy P3 Trailer Brake Controller?

Question

Question:

How do you unplug the connector on the prodigy brake control?

asked by: John W

1

Helpful Expert Reply:

To disconnect the Tekonsha Prodigy P3 Trailer Brake Controller # 90195 you will need to lift the end of the retainer on the Harness # 20127. This will allow you to remove it from the controller. A Pick Tool # 301-17144 may be needed if you cannot easily access this part of the controller.

expert reply by: Bud M

1

Answer 1

Hello Alex, thanks for reaching out. We actually custom make our own wiring kit which is designed specifically for this purpose. You can use the Universal Installation Kit #ETBC7. This kit will contain all of the components needed to upgrade your…

view full answer...

Answer 2

The connector for the Tekonsha Plug-In Wiring Adapter #3070-P is located above the parking brake on your 2023 Honda Ridgeline. Even knowing where it is still proves difficult to get to the connector and attach the wiring adapter. I know several…

view full answer...

Answer 3

Hey Jonathan, We haven't heard of any issues with the P3 #90195 and plug-in harness #3070-P with a 2024 Honda Ridgeline. How are you sure that the brakes are being applied on your Honda when applying the manual override on the P3? What are you…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

How Do You Unplug The Wiring Connector On Tekonsha Prodigy P3 Trailer Brake Controller?

Continue Researching