Trailer Wiring Recommendation for 2021 Tesla Model Y

Question

Question:

what do you recommend on wiring harness to fit the tesla 2021 model y? something that you wont have to cut wires, integrate with the software of the tesla car, suitable to tow rv on the back.

asked by: Michael

0

Expert Reply:

The ZCI Circuit Protected Vehicle Wiring Harness # 119250KIT will be the best option for a no-splice wiring harness for your 2021 Tesla Model Y. The kit will completely bypass the factory wiring. It uses sensors that clamp on to the factory wiring and detect electrical current, so no cutting or splicing will be needed.

I have linked our install video below if you want to take a closer look.

expert reply by: Jameson C

0

Answer 1

Hey Dale, No, the ZCI Circuit Protected Vehicle Wiring Harness w/ 4-Pole Flat Trailer Connector and Installation Kit #119250KIT is only compatible with 12v systems. Since Tesla switched over to 16v batteries in 2022 you'll need to purchase a step…

view full answer...

Answer 2

The best wiring harness for your 2023 Tesla Model 3 is going to be the T-One Vehicle Wiring Harness item #TK35VR. This harness is custom-fit and plugs into existing wiring in the rear cargo area. This will give you a 4-way connector to control your…

view full answer...

Answer 3

Hey Bryan, yes the ZCI kit part #119250KIT does 2023 Tesla Model 3.

view full answer...

Answer 4

Good question, Kurt! It took me a minute to figure it out, but the is one very minor difference. That being, the #119250KIT includes an added circuit tester (see pictures below). The actual wiring part ( #119251 ) is exactly the same for both parts.…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Trailer Wiring Recommendation for 2021 Tesla Model Y

Featured Help Information

Miscellaneous Media

Continue Researching