How Many Bolts Are Used To Mount The Curt 5th Wheel Brackets To The Frame Of A 2012 Chevy Silverado

Question

Question:

Per the directions I am supposed to have 4 holes through Frame to mount side brackets but I only have 2 so curious if that is fine or if there is a different mount for my specific application

asked by: Chris B

0

Expert Reply:

On 2016 and newer models there's weld nuts available for you to insert two more bolts in the brackets for the Curt Custom Fifth Wheel Installation Kit for Chevy/GMC # C16411-204. Since you have a 2012 you're good to go with just the two bolts you referenced. In the attached video below where Dave installs these on a 2013 you'll see he only uses two bolts on the side brackets when attaching them to the frame.

expert reply by: Kevin C

0

Stephanie

2/25/2025

I actually am looking for those bolts that bolt to the frame. Is there a certain name for them? I’ve looked around everywhere and cant seem to find them.

Kevin C.

3/6/2025

@Stephanie The bolts can easily be found at your local hardware store chain. If you have a 2015 or older model you'll need some 5/8"-11 x 1-3/4" Grade 8 Yellow Zinc Finish Hex Cap Screws, 5/8" split lock washers, 5/8" flat washers, and 5/8" flange nuts. For 2016 and newer models you'll need M16-2.0 x 35 mm Hex Cap Screws/Grade 8.8 / Zinc, 5/8" split lock washers, and 5/8" flat washers and would thread into factory weldnuts in the frame.

Answer 1

If you are using a universal installation kit, #RP30035, and your 1999 Ford F-250 is a light duty (under 8,500 pounds GCVW) then from the rear edge of the truck bed to the back of the rear rail is 29-1/4 inches. If you have a Super Duty F-250, it is…

view full answer...

Answer 2

The correct placement of the fifth wheel hitch will vary from vehicle to vehicle. It can also vary according to the type of install kit being used. Typically, the hitch will be installed so that the trailer king pin will be directly over or slightly…

view full answer...

Answer 3

The rails in the bed of your pickup are installed so that the king pin will be just forward of the rear axle when hitched. The mounting location is vehicle specific and if you would like to provide your trucks year, make, model bed length and cab…

view full answer...

Answer 4

If you are referring the Reese Select Plus 5th Wheel Trailer Hitch #RP30081, then yes all it takes is 4 pins to secure the hitch into the rails installed in the bed of your truck.

view full answer...

Answer 5

There are 2 different L-brackets included with Curt universal installation kit #C16200. The taller ones are 7 inches tall, 2-1/2 inches wide, and the top part of the L sticks out 4 inches. The shorter ones are 5-3/4 inches tall, 2-1/2 inches wide,…

view full answer...

Answer 6

The easiest custom installation kit for a 1999 Ford F-250 is going to be #RP56005-53. The frame brackets mount on the outsides of the frame rails and there is minimal drilling. I have included links to the installation instructions and a link to a…

view full answer...

Answer 7

The easiest way to install the bolts will probably be to have someone else help hold it in place while you mark for drilling and mount the adapter. Taking the pin box off the fifth wheel will just make unnecessary work for you. I've attached an…

view full answer...

Answer 8

The answer to your question will depend on the nature of the front of the 5th wheel you purchase. It looks like your Coachmen Chaparral has the rounded nose, so you might get by without a slider on flat ground but given the consequences of what could…

view full answer...

Answer 9

There are a couple of options that'll work great with your Lippert Turning Point Pin Box, however one hitch stands out to me more than others. Take a look at the: -Curt E16 5th Wheel Trailer Hitch - Slide Bar Jaw - 16,000 lbs #C16115 This 5th…

view full answer...

Answer 10

Since you have the Lippert Turning Point pin box you would not need a slider hitch such as #RP30051. You would need a fixed hitch such as #RP30047. The Turning Point pin box moves the pivot point of the trailer back which is why a slider hitch…

view full answer...

Answer 11

If your rails are ISR (Industry Standard Rails) then yes, you can easily swap out your 16k sliding 5th wheel hitch for a Curt A20 5th Wheel Trailer Hitch w/ R20 Slider - Dual Jaw - 20,000lbs #C16541. An easy way to see if the rails are ISR is to…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

How Many Bolts Are Used To Mount The Curt 5th Wheel Brackets To The Frame Of A 2012 Chevy Silverado

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching