Is 4 Bolts Adequate to Install a Fifth Wheel Rail Kit in a Truck Bed

Question

Question:

I just had a fiftwheel installed in my truck and was surprised to see only 4 screws out of 12 are actually going to hold this unit to the frame is this a good installation

asked by: Marcel

1

Helpful Expert Reply:

If you are referring the Reese Select Plus 5th Wheel Trailer Hitch # RP30081, then yes all it takes is 4 pins to secure the hitch into the rails installed in the bed of your truck.

expert reply by: Jameson C

1

Answer 1

For your 2015 Ford F-350 Diesel, I recommend starting with the Reese Quick-Install Custom Installation Kit w/ Base Rails for 5th Wheel Trailer Hitches #RP50026-58. These rails and brackets are compatible with the Diesel Exhaust Fluid tank on your…

view full answer...

Answer 2

If you are still feeling a bit of side-to-side sway even with a leveling system in your 5th wheel camper, the Ultra-Fab 5th Wheel King Pin Tripod Stabilizer #UF19-950001 will absolutely help minimize the movement you are feeling. It holds the king…

view full answer...

Answer 3

If you are using a universal installation kit, #RP30035, and your 1999 Ford F-250 is a light duty (under 8,500 pounds GCVW) then from the rear edge of the truck bed to the back of the rear rail is 29-1/4 inches. If you have a Super Duty F-250, it is…

view full answer...

Answer 4

The correct placement of the fifth wheel hitch will vary from vehicle to vehicle. It can also vary according to the type of install kit being used. Typically, the hitch will be installed so that the trailer king pin will be directly over or slightly…

view full answer...

Answer 5

The two rail hardware kits #RP58504 and the #RP58430 basically fit the rail kits. One includes lock nuts ( #RP58430 ) whereas the #RP58504 does not. But both are listed as fits for same rail kits. Worth mentioning though is #RP58504 comes with Grade…

view full answer...

Answer 6

The correct Reese Custom 5th Wheel Mounting Brackets for your 2011 Ford F-250 is with the part #RP50026. These custom brackets eliminate the need to drill into the frame of your F-250 and will drastically cut down on installation time. For the…

view full answer...

Answer 7

The rails in the bed of your pickup are installed so that the king pin will be just forward of the rear axle when hitched. The mounting location is vehicle specific and if you would like to provide your trucks year, make, model bed length and cab…

view full answer...

Answer 8

The easiest way to install the bolts will probably be to have someone else help hold it in place while you mark for drilling and mount the adapter. Taking the pin box off the fifth wheel will just make unnecessary work for you. I've attached an…

view full answer...

Answer 9

The easiest custom installation kit for a 1999 Ford F-250 is going to be #RP56005-53. The frame brackets mount on the outsides of the frame rails and there is minimal drilling. I have included links to the installation instructions and a link to a…

view full answer...

Answer 10

There are 2 different L-brackets included with Curt universal installation kit #C16200. The taller ones are 7 inches tall, 2-1/2 inches wide, and the top part of the L sticks out 4 inches. The shorter ones are 5-3/4 inches tall, 2-1/2 inches wide,…

view full answer...

Answer 11

On 2016 and newer models there's weld nuts available for you to insert two more bolts in the brackets for the Curt Custom Fifth Wheel Installation Kit for Chevy/GMC #C16411-204. Since you have a 2012 you're good to go with just the two bolts…

view full answer...

Answer 12

Hey William, thanks for reaching out! Gooseneck hitches and 5th wheel brackets use the same mounting locations, so you won't be able to install them together, but we have a wide variety of gooseneck to 5th wheel adapters that allow you to use…

view full answer...

Is 4 Bolts Adequate to Install a Fifth Wheel Rail Kit in a Truck Bed

Featured Help Information

Miscellaneous Media

Continue Researching