Lift Kit that Fits 2016 Lance 1995 Camper

Question

Question:

I want to raise my Lance 1995 trailer up at least 2 what kit would fit my 2016 Lance 1995 with dual Dexter torsion axels?

asked by: Gregg W

1

Helpful Expert Reply:

Your Lance 1995 travel trailer has tandem axles, and a GVWR of 5,700 lbs from what I could find, so it sounds like you have number 10 Torflex axles with 2,300 to 4,000-lb capacities. If this is the case # K71-707-02 would be the lift kit for your trailer. It provides 2-5/8 Inch of lift and is for tandem axle trailers.

expert reply by: Jameson C

1

Answer 1

If you are comfortable working with tools then the install of the Torflex Lift Kit #K71-707-02 will take you about a day. There is a great customer review that says it took him 6 hours to complete the installation at home. If you will be taking it to…

view full answer...

Answer 2

Based on some research, I was able to find out that your tandem axle 2019 Lance 1995 travel trailer has a GVWR of 5,700 lbs, and does use Dexter Torflex torsion axles like you mentioned, so the correct lift kit is the Torflex Lift Kit - Tandem Axle…

view full answer...

Answer 3

Rivets need to be drilled out so you'd need to find a drill bit thats a little smaller than the rivet and drill through them till they fall out. You do not need special hardware to mount #TLA8102 to your brackets either. Nuts and bolt that are…

view full answer...

Answer 4

Your Dexter 5,200 lb torsion axles will use the Torflex Lift Kit - Tandem Axle - 2-7/8" Lift #K71-724-02. This is a 2-7/8 inch lift that will work well with your trailer.

view full answer...

Answer 5

We offer four different axle lift kits for the Dexter Torflex axles. The difference between these kits is based on the weight capacity of the axle or tandem axles. There will be a tag on the axle shaft that will have the information needed to…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 12

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Lift Kit that Fits 2016 Lance 1995 Camper

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching