Parts Needed to Convert a Boat Trailer From Rollers to Bunk Boards
Updated 06/29/2023 | Published 06/28/2023
Products Featured in This Question
Question:
Hello . I’m looking to convert my 2003 6900#capacity load Rite trailer from roller to bunk style. The boat is a 2120 parker pilot house V bottom 21* deadrise with OB motor. Ive sent a few photos along. If you could advise if this is doable for this trailer? Are there conversion kits available from you and how much could I plan on spending to do such a conversion . I’ve owned the trailer since new and all is still in orettt good shape , Ive bought tires and brake and hub kits from you in the past for this trailer Thank you for you Time.
asked by: Neil T
Expert Reply:
This can absolutely be done. While there are not "kits" for doing the conversion, we do have the parts that you will need. These are not kitted together because each boat/trailer combination is different, so it is easier to not kit them.
It is recommended to have bunk boards that are at least 50% of the length of your boat. You can have longer boards if you would like, but you want at minimum 50% of the length. Since your boat is 21', you will want bunks that are at least 10.5' long. I would just round up to 11'. I have included the parts needed to make the conversion to 11' bunk boards below.
- CE Smith 5' Carpeted Bunk Boards # CE27820 (x2)
- CE Smith 6' Carpeted Bunk Boards # CE27840 (x2)
- CE Smith Bolster and Swivel Bracket Assemblies # CE10000G-4 (x2)
- CE Smith U-Bolts # CE15283GA-4 (x2)
(click to enlarge)
Product Page this Question was Asked From
CE Smith Carpeted Bunk Boards for Boat Trailers - 5' Long - 1 Pair
- Boat Trailer Parts
- Bunks
- Bunk Boards
- 3-3/4 Inch Tall
- 1-3/4 Inch Wide
- 60 Inch Long
- CE Smith
more information >
Continue Researching
- Search Results: spindle wear ring
- Search Results: spindle wear sleeve
- Search Results: 84 spindle sleeve
- Shop: Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2 - Pre-Greased
- Shop: DeeMaxx Trailer Idler Hub for 3,500-lb Axles - 5 on 4-1/2 - Threaded - Galvanized
- Shop: Hydrastar Disc Brake Kit w/ Actuator for Single Axle Trailers - Slip On Rotor - 5 on 4-1/2 - 3.5K
- Shop: CE Smith Trailer Idler Hub Assembly w/ Case for 3.5K Axles - 5 on 4-1/2 - Galvanized - Pre-Greased
- Video: Comprehensive Review: Hydrastar Electric Over Hydraulic Actuator for Disc Brakes
- Shop: Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2 - Galvanized
- Shop: Hydrastar Disc Brake Kit w/ Actuator for Tandem Axle Trailers - Slip On Rotor - 5 on 4-1/2 - 3.5K
- Shop: Hydrastar Disc Brake Kit w/ Actuator for Tandem Axle Trailers - Slip On Rotor - 6 on 5-1/2 - 6K
- Search Results: bunk boards boat trailer parts
- Search Results: boat trailer bunk brackets
- Search Results: boat trailer bunks
- Search Results: bunk kit
- Video: All You Need to Know About the Replacement Endcap for CE Smith Boat Trailer Roller Bunks
- Video: CE Smith Double U-Bolt Bolster and Swivel Bracket Assemblies Review
- Video: Dutton-Lainson Boat Trailer Roller Bunk Bracket Installation
- Q&A: How Much Roller Shaft Length will Yates Endcap for Side Guide Rollers # YR224-4 End Up Taking up
- Q&A: Recommended 5' Bunk Boards and Mounting Hardware For Boat Trailer
- Q&A: Converting Boat Trailer From Rollers to Bunk Boards
- Q&A: Parts Needed to Switch a 98 Shoreland'r Trailer From Rollers to Bunks
- Video: Yates Side Guide Roller for Boat Trailers Spec Review
- Q&A: How To Convert a Boat Trailer from Center Rollers to Bunk Rollers
- Q&A: Centering Boat On Trailer With Wobble Rollers
- Q&A: How Many Support Brackets Are Needed For A 14 Foot Bunk Board Carrying A Pontoon Boat?