Parts Needed to Switch a 98 Shoreland'r Trailer From Rollers to Bunks

Question

Question:

Curious if there are parts or a kit to convert my 98 shorelandr trailer from rollers to bunks? If anyone knows the parts I need and purchase from you? Thanks for any advice

asked by: Chris

0

Expert Reply:

While there is no specific kit for switching your 98 Shoreland'r from rollers to bunks, it should be relatively straight forward. It looks like your rollers should be bolted on, so you should be able to remove those and then add bunks. You will need CE Smith Carpeted Bunk Boards # CE27820, CE Smith Bolster and Swivel Bracket Assemblies # CE10001G-4 and CE Smith U-Bolts # CE15283GA-4.

I have also linked our selection of bunk boards in case you need a different length. I recommend getting bunk boards that match the length your rollers currently cover.

expert reply by: Scott S

0

Answer 1

For the bunks I recommend using two sets of the 5' CE Smith Carpeted Bunk Boards #CE27820, or you'd like to get your own wooden boards you can wrap them in Marine-Grade Carpeting #CE11349. To install the boards, you will need a pair of…

view full answer...

Answer 2

Thanks for the picture! While we do not have an exact replacement for a Profile 2000 winch we do recommend the Dutton-Lainson Hand Winch item #DL14627 as a replacement. This winch has an 1,800 lbs capacity and will work great with the 20' x…

view full answer...

Answer 3

I can certainly understand not wanting to have to connect 2 five-foot carpeted bunk rails like #CE27820 to get the 10 foot bunks you need. We don't offer them in the 10' length because the shipping costs would be more expensive than the bunks…

view full answer...

Answer 4

The CE Smith Carpeted Bunk Boards for Boat Trailers part #CE27820 are made with untreated lumber. If you want treated you can purchase your own boards and wrap them with the CE Smith Deluxe Marine-Grade Carpeting for Bunk Boards part #CE11330.

view full answer...

Answer 5

I have attached a chart for you to take a look at that includes the lug nut torque specifications. If your wheel uses 1/2 inch lug nuts or wheel bolts like the 12 Inch Steel Spoke Trailer Wheel #AM20124 referenced in your question, you will torque…

view full answer...

Answer 6

Ideally you want bunk boards that are at least 50% of the length of your boat, and want the to run from the stern and as far forward as you like. Since your boat is 16' Long you will want at least 8' of bunk boards, but I recommend going with…

view full answer...

Answer 7

Hey Tyler. We do not have any center caps that fit a 4.58" diameter pilot hole. You said you measured and got an outside diameter of 116.38 mm. What exactly did you measure? Center caps like the item #LHCS109-SI60C you were looking at are sized…

view full answer...

Answer 8

Based on the picture you submitted the Fulton Marine Jack part #FXP100W0301 that you referenced would be exactly what you'd need and would bolt right up to the mount you have on the trailer frame.

view full answer...

Answer 9

We have a really great option for a trailer for your 10 foot Bass Pro Pond Prowler boat, although the Malone trailer you mentioned has been discontinued by the manufacturer and is no longer available. Instead, which I highly recommend is an option…

view full answer...

Answer 10

It might be possible to repair the winch you have currently but without knowing what winch you have it's really pretty hard for me to say if that's possible or not. Most likely it's time for an all new winch like the Dutton Lainson part…

view full answer...

Parts Needed to Switch a 98 Shoreland'r Trailer From Rollers to Bunks

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching