Do I Need to Install a Jumper Wire On the H4 Connector When Switching From Lead to AGM Batteries?
Updated 12/30/2024 | Published 06/28/2023
Question:
I have a PD 4060CSV converter charging section. Im upgrading to AGM batteries from lead acid. Do I need to do something with the H4 pin connection? it says off=lead, on=gel ?? Or do I just install the AGM batteries and Im good to go? Thanks!
asked by: Craig L
Expert Reply:
When you install your AGM batteries you won't need to flip that switch on the Replacement Converter Section for Progressive Dynamics Inteli-Power 4000 Series 60 Amp Power Center # PD4060CSV.
You'd only need to flip it if you were using Lithium Ion batteries. However for that H4 connector you are going to want to leave it off for lead.
The instructions only recommend installing that jumper if you're using gel batteries, and while AGM batteries do have some gel in them they are not quite the same and have different charging patterns.
(click to enlarge)
Product Page this Question was Asked From
Replacement Converter Section for Progressive Dynamics Inteli-Power 4000 Series 60 Amp Power Center
- Accessories and Parts
- Power Converter
- Converter Section
- 60 Amp
- Progressive Dynamics
more information >
Continue Researching
- Shop: Replacement Converter Section for Progressive Dynamics Inteli-Power 4000 Series 60 Amp Power Center
- Video: Review of Progressive Dynamics - RV Converters - PD4060CSV
- Shop: Replacement Converter Section for Progressive Dynamics Inteli-Power 4000 Series 45 Amp Power Center
- Shop: Progressive Dynamics 4000 Series RV Converter w/ Charge Wizard and AC/DC Distribution Panel - 60 Amp
- Video: Progressive Dynamics RV Power Control Center Installation - 2017 Airstream Flying Cloud Travel Trail
- Q&A: How to Use Lithium Batteries With a PD4060K Converter/Panel That Does Not Have the Li Switch
- Q&A: Solution for Needing 60 amp Converter/Panel that Can Do Lead Acid and Lithium
- Q&A: Replacement Converter Section for Progressive Dynamics PD4060K for Lithium Batteries
- Q&A: Does Lithium Battery Really Need a Different Charging Setup Than Other Batteries
- Shop: B&B RV City Water Inlet with Plastic Flange - Brass Check Valve - Surface Mount - Black
- Search Results: rv vents and fans accessories and parts
- Search Results: ventline
- Search Results: ventline screens replacement
- Video: Ventline E-Z Lift Ventadome Trailer Roof Vent Feature Review
- Video: Ventline RV Vents and Fans BVC0573-41 Review
- Video: In-Depth Review of the Ventline Ventadome Trailer Roof Vent
- Video: Breaking Down the Ventline Ventadome Trailer Roof Vent
- Search Results: pd4045csv
- Search Results: pd4060csv
- Shop: Blue Ox Adjustable Drop Hitch Receiver Adapter - 2" Hitches - 8" Rise/Drop - 10,000 lbs
- Video: What to Know About the Blue Ox Adjustable Drop Hitch Receiver Adapter
- Search Results: dura faucet
- Search Results: outdoor shower accessories and parts
- Q&A: Is There A Soft Start Compatible With A Coleman RV Air Conditioner?
- Shop: Ventline Ventadome Trailer Roof Vent - Manual - 14-1/4" x 14-1/4" - Smoke
- Shop: Ceiling Garnish for Ventline Roof Vent - 5-1/8" Leg - 14-1/4" x 14-1/4" - Birch White
- Q&A: Parts Needed For Flat Towing A 2014 Mini Cooper
- Q&A: Can the Converter Section of a PD4045KA Be Upgraded to 60amps and Charge Lithium Batteries
- Shop: RV Mattress
- Shop: Trailer Hitch
on Accessories and Parts
John H.
12/28/2024
I don’t believe he’s talking about the lithium ion switch. If you look right next to the switch, there is a two pin jumper that shows off for lead and on for gel. He asked the same question I need to know. If I’m running AGM batteries (which I am), do I need to put a jumper in this location? Thanks.