Recommended RAS Kit for a 2013 Pleasure-Way Excel Motorhome on a 2012 E-350 Cab and Chassis

Question

Question:

Looking for the correct Rad Active Suspension Kit for 2013 Pleasure-Way Excel TD motor home built on a 2012 Ford E350 Super Duty chassis.

asked by: Richard Q

0

Expert Reply:

I checked with Roadactive and the correct RAS Kit for a 2012 Ford E-350 chassis is the RoadActive Suspension Custom Leaf Spring Enhancement Kit item # RAS2612. This kit is designed specifically for the commercial cargo van frame that your motorhome is built on.

expert reply by: Jerred H

0

Answer 1

Hi Josh; this can get pretty confusing with the E-Series since the manufacturer doesn't officially list or update fitment for their wiring harness on the cutaway. However, I can confirm the Tekonsha Prodigy P2 #TK49UR comes with the wiring…

view full answer...

Answer 2

Hey Paul, so your 2024 motorhome built on a Ford Cutaway chassis does have a 7-way at the rear and brake controller install wiring under the dash so all you'd need is the part #TK99UR which comes with the P3 brake controller and the correct…

view full answer...

Answer 3

Hannah, you’ll be in good shape with the gas powered Velit RV Heater #VE46QV for sure. Both the diesel and gas Velit heaters put out the same 14,000 BTUs and are rated down to -30°F operating temp. In real-world use, the only real difference is…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Hey Ben, since we know your 2025 Gulfstream 6327le is built on a Class C Ford E-350 chassis you would want the Roadmaster front sway bar part #RM-1139-176 as a confirmed fit. This will do a great job improving the handling and stability of the RV. Do…

view full answer...

Answer 12

Hey Jonathan, congrats on the new truck! The Universal Mounting Panel item #331-TPSI-001 is what you'll need to install the control knob of the Redarc Tow-Pro Liberty item #RED53CR in your 2026 Nissan Frontier SV. It measures 1-8/16" tall x…

view full answer...