Can B and W Continuum Weight Distribution be Used with Air Lift Bags

Question

Question:

Does BandW continuum works with Airlift 5000 installed on 2020 Ram 1500? Any negative effects having BandW installed with Airlift system?

asked by: Chris S

0

Expert Reply:

Yes, you can use the B and W Continuum # BW78FR an Air Lift air bag kit # AL88375 on your 2020 Ram 1500. You would want to first decide how much air pressure in the bags you want and then setup up the Continuum and you'd be set.

expert reply by: Jameson C

0

Answer 1

Hey Tim, the Brandmotion FullVUE Digital Rear View Mirror with HD Backup Camera #BM86YR that you referenced does come with a camera in the third brake light/CHMSL location that you asked about. I attached a picture that shows the contents of the kit…

view full answer...

Answer 2

Hello Dan, Definitely on the right road to a smoother ride (pun intended). I would say that you knowing you are on the heavier end of the tongue weight you are safe finding one around the 1k mark. You just want to make sure you are closer to the…

view full answer...

Answer 3

Yes, you can use the Reese Friction Sway control part #83660 without a weight distribution system. You would just need to use the tab part #RP26003 on the ball mount as well.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Can B and W Continuum Weight Distribution be Used with Air Lift Bags

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching