Correct Air Lift 5000 Kit for a 2016 Toyota Sequoia SR-5

Question

Question:

There are 2 kits to choose from for 2016 sr5 Toyota Sequoia 4x4. What is the difference?

asked by: Richard O

0

Expert Reply:

Since your 2016 Toyota Sequoia is the SR-5 you need the Air Lift 5000 Kit # AL60786. The other kit is for a non-SR-5 Sequoia.

If you'd like the ability to monitor and adjust your air bags on the fly I recommend installing the Air Lift Air Shock Controller Compressor System # AL25804 as well.

expert reply by: Jon G

0

Answer 1

Both Air Lift LoadLifter 5000 Ultimate Air Helper Springs, part #AL84JQ for normal springs or part #AL24JQ for internal jounce bumpers, will fit the 2WD and the 4WD versions of the 2022 Toyota Tundra so you're good to go! I always recommend…

view full answer...

Answer 2

The Air Lift Air Shock Controller Compressor, part #AL25804 includes the onboard compressor; dash mounted gauge panel; hardware and air lines. An air tank isn't included. Since the compressor is manually operated from the dash panel, a pressure…

view full answer...

Answer 3

Hi Chris! There are not a lot of options that are a fit for an 02 Dodge Ram 3500 with an in-bed gooseneck or 5th wheel hitch (which is what I assume you mean by pintle hitch, but if I am wrong, please let me know). The only option that is will be the…

view full answer...

Answer 4

Thank you for the photo and you definitely need some suspension help there on your 2008 Toyota Sequoia SR5 with the sag you have. Since you have the SR5, so long as your Sequoia does not have auto leveling, the air spring system you need is from Air…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...