Distance Between Mounting Bolts of Demco Spare Carrier part # DM15850-52

Question

Question:

WHAT IS THE DISTANCE BETWEEN THE TWO BOLTS THAT BOLT TO THE STAKE POCKET

asked by: Brett T

0

Expert Reply:

The distance between the bolts of the Demco Spare Carrier part # DM15850-52 that hold it to the stake pocket of the trailer is 4-5/8 inches.

expert reply by: Jameson C

0

Answer 1

I spoke with my technical contact at Curt and he informed me that the Curt Hitch #C15810 will fit spare tires with a wheel size of less than 20 inches. We happen to have a Ford F-350 on site, so we checked out the spare tire underneath and it was a…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 6

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hey Scott! Yes, there is an option that will work with your 20" spare. The Draw-Tite Trailer Hitch Receiver #DT45508 does not have the same spare tire size restriction as the Curt. This is also a Class V hitch with a 2-1/2" receiver and a…

view full answer...

Distance Between Mounting Bolts of Demco Spare Carrier part # DM15850-52

Product Page this Question was Asked From

Continue Researching