What is Needed to Install Replacement Rear Wheel Holder Assembly for Thule ProRide Bike Rack

Question

Question:

How do I remove old wheel cradle

asked by: Byron

0

Expert Reply:

To change the wheel cradle on the Thule ProRide XT Roof Bike Rack # TH598004, grip the cradle on its sides, pull it apart a bit and pull it off. Then just slide on the Replacement Rear Wheel Holder Assembly for Thule ProRide or ProRide XT Roof Bike Rack # TH74VW.

expert reply by: Kyle S

0

Answer 1

Yes, the Replacement Rear Wheel Holder Assembly #TH74VW is exactly what you need for your Thule UpRide Roof Bike Rack #TH599000.

view full answer...

Answer 2

Yes, we do Jorge! To get the straps for a Thule Upride item #TH599000-FB you'll want the Fat Bike Adapter item #TH599100. The straps are built into the adapter you can't purchase just the straps. What kind of bike do you have?

view full answer...

Answer 3

Hello John, No, the #TH73WH is designed for the Outride. For the Thule Upride you want the Replacement Rear Wheel Holder Assembly for Thule #TH74VW. I included a review video for the product to check out. Happy Holidays to you and your family, from…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

What is Needed to Install Replacement Rear Wheel Holder Assembly for Thule ProRide Bike Rack

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching