Brake Mounting Flange Bolt Pattern for 3.5K 95" Long Dexter Trailer Axle

Question

Question:

What is the brake backing plate 4 bolt pattern measurements? Thanks

asked by: Mark R

0

Expert Reply:

The brake mounting flange on the Dexter Trailer Axle Beam with 4" Drop E-Z Lube Spindles # 7685269 has mounting holes that are 2-7/8" apart on center (see attached).

expert reply by: Jon G

0

Brake Mounting Flange Bolt Pattern
(click to enlarge)

Answer 1

We do indeed, the #BP10-060 brake adjuster for 10 or 12 inch hydraulic brake assemblies fits Dexter, Demco and Dico 10" Hydraulic trailer brake assemblies, so it would work great for you. If you also need a new adjuster spring, use #046-083-01

view full answer...

Answer 2

I would be happy to help! Since your brake assembly is stamped K23-462-00 you will want to go with the Dexter Electric Brake Assembly for 4.4K Axles #K23-462-00 and you can confirm that this is the correct assembly and not just an incorrect sticker…

view full answer...

Answer 3

Though I would not be able to answer for parts that are on your trailer now, it is a good idea for your brakes to match your axle's weight capacity. As for a replacement, I could not find a reference to the brakes you have now, and the only…

view full answer...

Answer 4

The correct replacement shoes for the Dexter Electric Trailer Brakes #23-180 are going to be part #AKBRKR-S-12, which will replace the shoes on 1 Dexter brake assembly. You'll want to order 2 if you have a single axle or 4 if you're replacing…

view full answer...

Answer 5

You measured the drop correctly. It would be from the center of the axle to the center of the spindle. That dimension would be the drop. See picture I attached.

view full answer...

Answer 6

Hello Jerry, Great question. It all depends on on if it is compatible. If your current set up is not a topwind coupler then it isn't going to work because the #GCSQTW-30008 does not use traditional pin-adjustment holes (please refer to picture I…

view full answer...

Answer 7

If your Land Cruiser was equipped with the factory installed 7-way trailer connector at the rear bumper, it will have the brake controller connector located under the dashboard. The connector will be taped to another wiring harness somewhere near the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Brake Mounting Flange Bolt Pattern for 3.5K 95" Long Dexter Trailer Axle

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching