Correct Grease Seal for Lippert LCI35 Axle

Question

Question:

Trying to determine which seals I need for a Lippert Axle. The Part # is: LCI35-SB-80-65.25-NOSP-US-L-545-7213-18PT-GAWR 2800#. Thanks for any assistance.

asked by: John W

1

Helpful Expert Reply:

For your Lippert LCI35 Axle, you'll need the Grease Seal part # 58846 which has a 1.719" inner diameter and 2.565" outer diameter.

expert reply by: Conner L

1

Answer 1

The biggest issue we see with the Furrion Vision S Wireless RV Backup Camera Systems like part #FOS43TASF comes from the wiring on the vehicle side, the running light circuit in particular. If it's less than 12 volts then the camera won't be…

view full answer...

Answer 2

We do have the exact seal you are lookin for with the part #58846 which is for the 3,500 lb trailer axle you have and has an inner diameter of 1.719 inch and an outer diameter of 2.565 inch.

view full answer...

Answer 3

Nothing at all. The Grease Seal item #58846 is a different part number for the 10-19 grease seal. It has a inner diameter of 1.719" and outer diameter of 2.565". This seal is primarily used in 3,500 lbs axles. What kind of trailer do you…

view full answer...

Answer 4

Yes, you'll want to replace the grease seals when packing the bearings but the grease cap can be reused if it's still in good condition. If you don't know what bearings and seals you need, I have a few options for you to help with…

view full answer...

Answer 5

I have attached for you below the brake adjustment procedure for Lippert self-adjusting braking assemblies. 1. Jack up coach and secure on adequate capacity jack stands. Follow coach manufacturer’s recommendations for lifting and supporting the…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Correct Grease Seal for Lippert LCI35 Axle

Product Page this Question was Asked From

Continue Researching