Availability of Sway Bar Bracket that Fits Gen-Y Adjustable Ball Mounts

Question

Question:

Do you still carry the adapter that fit on the gen y hitch that went around the ball pointing down not being used that has the small ball on it allowing you to hook a sway bar up to the hitch? I recently got a new torsion flex 16k pound boss 2.5”

asked by: James G

0

Expert Reply:

We do have an adapter for the Gen-Y adjustable ball mounts that allows it to be used with sway control with the part # 325-GH-300-1.

expert reply by: Jameson C

0

Answer 1

Hey Joey! I reached out to Gen-Y and they said the Dual Sway Control Bracket for Gen-Y Adjustable Ball Mounts #325-GH-300-1 cannot be mounted in the inverted position. Unfortunately, if you want to use the bracket those tabs have to be at the bottom…

view full answer...

Answer 2

Friction sway control units like #83660 do need to be either disconnected or to have their tension control released when you reverse the trailer. Otherwise the unit is likely to be damaged. In normal operation these devices will make some grinding…

view full answer...

Answer 3

You can pretty easily install a friction sway control system on the driver side of a trailer. You would just need to remove the inner piece of the system like part #83660 and then rotate it 180 degrees and reinsert it into the outer piece. You would…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hey David, it sounds like you know what you're doing but I've also gone ahead and found the wiring diagram for the Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR for you to check out so you can use it as a cross…

view full answer...

Availability of Sway Bar Bracket that Fits Gen-Y Adjustable Ball Mounts

Product Page this Question was Asked From

Continue Researching