Replacement Trailer Bearings for L68149, LM67048 and Seal # GS-1719

Question

Question:

Is this the right kit the bearings do not match

asked by: Ricky

0

Expert Reply:

The bearing kit part # BK2-100 matches one of your bearings and your grease seal but it does not match everything so it would not be the correct kit to use. Since we don't have a kit that has everything your best option would be to get the parts individually. So for bearings you'd need the # LM67048, the seal # 58846, and bearing # L68149.

expert reply by: Jameson C

0

Answer 1

When the L68149 bearing is paired with the L68111 race, the 10-19 grease seal is used. However when the same bearing is used with the L68110 race on a boat trailer, the #168233 seal is usually used. You can verify this by using a digital caliper to…

view full answer...

Answer 2

We have the individual parts you need but not as a kit. You'd want the bearing part #LM67048 and #L68149. Since this is not a standard bearing combination I would need to know more info to pick out the seal. I'd need to know the diameter of…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Replacement Trailer Bearings for L68149, LM67048 and Seal # GS-1719

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching