What Tools are Needed to Install Curt Hitch # C57CR

Question

Question:

What tools are needed for the installation?

asked by: Scott

1

Helpful Expert Reply:

In the attached install instructions for the Curt hitch part # C57CR that you referenced a list of the needed tools is listed and you'll need a ratchet, torque wrench, 3/4 inch drive socket, slot screwdriver, 12 mm socket, and 13 mm socket.

expert reply by: Jameson C

1

Answer 1

As you can see of the photo I added for you, the crosstube will be totally concealed on your 2024 Hyundai Venue after installing the Curt hitch that fits, which is the following part number: - Curt Trailer Hitch Receiver #C57CR I also wanted to add,…

view full answer...

Answer 2

For your 2021 Hyundai Venue I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" #C57CR which is confirmed to fit your vehicle, and will not require any drilling or trimming to the fascia of your vehicle. The #C57CR is…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

What Tools are Needed to Install Curt Hitch # C57CR

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching