How To find The Correct Replacement Door Gasket For A 2013 Forest River R-Pod 194 Travel Trailer

Question

Question:

I need a gasget that goes around the rear kitchen lift door on a 2013 Forest River r-pod model 194

asked by: Joe K

0

Expert Reply:

To find the correct replacement gasket for the compartment door on your 2013 Forest River R-Pod 194 I would need to know the profile (shape) and dimensions. For example, the # SR35ZR is a half round shape that's 11/16" wide x 3/8" tall. If you can get me the dimensions and profile of your current gasket I'd be happy to find a replacement for you.

expert reply by: Kevin C

0

SR35ZR Dimensions
(click to enlarge)

Answer 1

Hey Doug, welcome back! The Leveling Scissor Jack - 24" Lift - 5,000 lbs item #JSC-24-IND and the Scissor Stabilizer Jacks - 18-3/4" Lift item #TJSCHD-24 are going to be made of the same 14 gauge steel. The difference in capacity has to do…

view full answer...

Answer 2

Hey Allen, thanks for reaching out. For bolting on the etrailer Scissor Stabilizer Jacks #e36VV the recommended hardware is self-tapping 3/8" x 1" screws. If you use that, you won't need any bolts or washers or anything. You'll want…

view full answer...

Answer 3

Hey Craig, thanks for reaching out. If your 2025 Rockwood 2318FT came with the SJ-2500 stabilizer jacks, I agree with you. They're functional, but they're pretty light-duty. My favorite upgrade is the etrailer Scissor Stabilizer Jack…

view full answer...

Answer 4

Hi Justin; do the leaf springs run under your axle (underslung) or are they sitting on top of the axle (overslung)? If you have the underslung configuration you can use the Dexter Trailer Springs Over-Under Conversion Kit #K71-384-00 you were looking…

view full answer...

Answer 5

Hi LeRoy! I went out to the warehouse and measured this directly for you, and the center to center distance between the two holes on the dogbone base is 6-1/2 inches. That measurement is consistent across our etrailer scissor jack variations,…

view full answer...

Answer 6

Hey Anthony, thanks for reaching out. The etrailer Scissor Stabilizer Jacks #e56VV are a solid and budget friendly option for your 2002 19 foot Nash. Each jack is rated for 2,500 lbs, which is more than enough when used as a pair for stabilizing a…

view full answer...

Answer 7

Hey Ginnie, generally it's best to have the scissor jacks like the part #TJSCHD-24 mounted to the trailer but if you are on level enough and sturdy enough ground then you could use them without installing them.

view full answer...

Answer 8

Hi Scott! You are absolutely correct. The same standard bolt would be used on both sides of the leaf spring, even when it is a slipper spring. The only exception to that would be if it was a wet bolt, as that would just leak grease everywhere and…

view full answer...

Answer 9

The MORryde Quick Connect RV Steps #MR25HR weigh 50 pounds.

view full answer...

Answer 10

Hi Susan, That part number comes up as a 60lb gas strut with a 20" extended length and 10mm socket so the Taylor Made Marine Gas Strut for Boat Hatches #3691843-60 would be a fit. To remove your current strut you'll need to stick a small…

view full answer...

Answer 11

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 12

Blane, what you're looking for is the 7-Leaf Double-Eye Spring for 8,000-lb Trailer Axles #DX74XR. This spring has a 4k capacity, will work with 8k axles, has 1 3/4" wide leaves. You'll notice that these springs are a bit shorter, but…

view full answer...

How To find The Correct Replacement Door Gasket For A 2013 Forest River R-Pod 194 Travel Trailer

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching