Lift Kit Recommendation for Utility Trailer with Single Axle

Question

Question:

Hello, I’m sure this has been asked and answered.. But I couldn’t find any info. I’ve got a carry-on utility trailer that we use around the farm. Due to or grosss overloading the tires will run the fender wells. It appears to have a 1.5” axle. Any options to lift it?

asked by: Anthony R

0

Expert Reply:

We have the Correct Track lift kit part # LC87120 that fits single axle trailers with leaf spring suspension like you have and can give you a lift of either 1-1/4 or 2-1/4 inch.

expert reply by: Jameson C

0

Answer 1

The over under conversion kits like #K71-385-00 only work on round axles. What you can do depends on why you need to raise the trailer. If you need more clearance under the trailer you can replace the leaf spring hangers with longer ones. You have to…

view full answer...

Answer 2

Axle flip kits are great options for raising the suspension of a trailer. Trucks weren't as tall back then as they are now so I'm not totally surprised your trailer is sitting so nose high. We have 2 inch square U-bolt kits like part #CE23103…

view full answer...

Answer 3

Thank you for providing that picture. Since you have a 3,500 lb torsion axle we know it is a Dexter #10 Torflex. This means the #K71-707-01 is indeed the correct lift kit for your trailer.

view full answer...

Answer 4

Best option for you would be to have the Stabilizer Jacks #TJ01RT-HD welded to your trailer frame. That will give you the most secure attachment. A local welder to you should have no problem attaching these. Would probably be the easiest job of his…

view full answer...

Answer 5

I have a couple recommendations as we do not recommend using lift blocks likes those used on a vehicle axle for a lift. First since your axle sits above your leaf springs you can use the Over-Under Conversion Kit #K71-384-00 to place your axle below…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Lift Kit Recommendation for Utility Trailer with Single Axle

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching