Shipping Weight of MORryde Cushioned 5th Wheel Pin Box for 14K to 18K Trailers with Lippert Rhino

Question

Question:

What is the shipping weight of the MR83QR?

asked by: Ernie

1

Helpful Expert Reply:

The shipping weight of the MORryde Cushioned 5th Wheel Pin Box for 14K to 18K Trailers with Lippert Rhino part # MR83QR is 165 lbs.

expert reply by: Conner L

1

Answer 1

Hey Pat, The Rhino box definitely is shorter than what most Rver's were hoping for so we get this question all the time. Switching to a MORryde Cushioned pin box designed with a Rhino box bolt pattern unfortunately won't give you extra…

view full answer...

Answer 2

The Rhinobox was definitely an unpopular choice for manufacturers to go with so swapping it out with the MORryde Cushioned 5th Wheel Pin Box for 18K to 21K Trailers w/ Lippert Rhino #MR55QR would definitely give you a major improvement in ride…

view full answer...

Answer 3

From the center of the front mounting holes to the center of the rear mounting holes on the MORryde Cushioned 5th Wheel Pin Box for 14K to 18K Trailers w/ Lippert Rhino #MR83QR measures 7-1/2" as shown in the included diagram. I included a video…

view full answer...

Answer 4

The Lippert Rhino Box has it's own bolt pattern so the Lippert 1621SHD #LC1387882 would not be a compatible fit. Instead you'll want a pin box like the MORryde Cushioned 5th Wheel Pin Box for 18K to 21K Trailers w/ Lippert Rhino #MR55QR,…

view full answer...

Answer 5

When adjusting the height of a pin box such as #LC1191191 it is important to support the pin box when removing the bolts. I recommend 2 or 3 buddies to give you a hand and make sure no one is beneath the pin box while raising or lowering it. With the…

view full answer...

Answer 6

I do have an option for you but there isn't a rotating pin box replacement for the Lippert Rhino. That said, you can still make full turns without this but you would need a sliding fifth wheel hitch like the B&W Companion OEM 5th Wheel…

view full answer...

Answer 7

Hey Ryan, Indeed there is a Sidewinder that has the correct bolt pattern to replace your Lippert Rhino pin box. I went ahead and verified directly with the manufacturer for you that the correct replacement is the following: - Reese Sidewinder 5th…

view full answer...

Answer 8

To convert the WFCO WF-8955PEC to be lithium compatible you'd need the part #PD4655V and you'd be set. This fits in the panel without any modifications.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Shipping Weight of MORryde Cushioned 5th Wheel Pin Box for 14K to 18K Trailers with Lippert Rhino

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching